Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 110

background image

RDA 400-450 S

Ver.3 29.06.2007

85

5.2

Troubleshooting chart

The Control Station does not op-

erate when the main switch is

switched on!

- See ”

5.1.1 Electric fault” on page 82

.

The bout marker(s) cannot be

unfolded!

- Check according to ”

5.1.1 Electric fault” on page 82.

- Check according to ”

5.1.2 Hydraulic fault” on page

- Check whether one of the bout marker indicator lamps

on the Control Station lights.

- Check whether the machine is in the low-lift mode.

(For safety reasons the bout markers cannot be un-
folded in the low-lift mode or at a higher height.)

- Check the low-lift switch. Disconnect the switch con-

nector from the Workstation and verify correct bout
marker operation.

- Check the wing unfolding switch. This switch blocks

the current signal from the bout marker valves when
the wings of the drill are retracted. This prevents a
bout marker from being unintentionally unfolded in
this position. Disconnect to the switch connector from
the Workstation and verify correct bout marker oper-
ation.

- Check the current supply to the two electric valves (A)

and (B) in the centre of the top surface of the valve
block. See ”

5.1.3 Hydraulic electric valves” on page

The bout marker valve(s) should receive current

when the corresponding indicator lamp lights.

The bout marker(s) cannot be

retracted!

- This is probably caused by contamination in an elec-

tric valve. Please note that contamination that causes
faults such as this often is not visible to the naked eye.
In this case, replacement of the electric valve is rec-
ommended.

- It should always be possible to retract both bout mark-

ers no matter which setting and indication are ob-
served on the Control Station and also when the
Control Station has been switched off.

«
...
83
84
85
86
87
...
»

Содержание Rapid RDA 400S















































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: Labnet Страницы: 5

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: TC Electronic Страницы: 14

Бренд: Access Страницы: 7

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: Billy Goat Страницы: 14

ARIEDO HDC 300W

Бренд: GSi Страницы: 28

Бренд: Nippon Genetics Страницы: 14

Groline HI981412

Бренд: Hanna Instruments Страницы: 44

Бренд: Focal Meditech Страницы: 10

Бренд: Rohm Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды