Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 110

background image

RDA 400-450 S

Ver.3 29.06.2007

83

5.1.3

Hydraulic electric valves

An electric valve contains a coil that operates as an electromagnet when current is fed to the valve.
Do as follows to check whether the valve receives current:

The LED on the connector lights and the coil becomes warm after a few minutes. Also, the nut on
the top of the valve becomes magnetic.

Use a small screwdriver or the edge of a knife blade to check whether the nut on top of the valve
is magnetic. Since residual magnetism may be present in the nut, perform this inspection with the
power switched on and off.

!

The bout marker valves (A) and (B) receive current when their indicator lamps on the Control
Station light and the machine is in the low-lift mode.

!

The lift stop valve (C) receives current when the lift stop is engaged or during lifts in the low-
lift mode.

!

The pre-emergence bout marker's electric valve (D) receives current when the tramline indica-
tor lamps on the Control Station light when the machine is in the low-lift mode.

OBS!

Signals to the bout marker and pre-emergence bout marker are not output from the Control

Station until the machine is set to the low-lift mode.

Figure 5.1

Figure 5.2

C

B D

A

«
...
81
82
83
84
85
...
»

Содержание Rapid RDA 400S















































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: Backyard Play Systems Страницы: 54

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Landoll Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды