Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 110

background image

Instructions and settings

48

Ver.3 29.06.2007

11

Radar, Yes/No. ("Yes" for hydraulic feed output.)

12

Number of radar pulses per meter of driven distance. Default setting 99/m. (Only applies

to hydraulic feed output.)

13

Number of pulses per wheel rotation. Default setting: 1.

14

Drive wheel circumference Default setting 240 cm.

15

AUTO

. Automatic calibration. Measure a given distance (at least 100 m). Press

at the starting point. This will reset the pulse counter. Drive the selected distance with the ma-
chine lowered to the drilling position. The pulses are counted in the display. Enter the driven
distance in metres. The Control station now calculates the number of pulses per metre of driven
distance, and automatically adjusts this value for the wheel circumference in menu 14 or the

number of radar pulses per metre driven distance in menu 12. Select OK by pressing

.

16

Alarm delay. Select the delay in seconds between receipt of the alarm signal from the

seed box rotation guard and the visual/audible alarm of the Control Station. The alarm should
be slightly delayed to avoid alarms at low speeds. Nevertheless, the delay should be as short as
possible to allow even sudden, brief interruptions. Default setting: 2.0 seconds.

17

Fan rpm, seed fan, upper alarm level. Default setting: 4800 rpm.

18

Fan rpm, seed fan, lower alarm level. Default setting: 3800 rpm.

19

Buzzer, On/Off

20

Pre-emergence bout marker, Yes/No

21

Side bout marker as pre-emergence bout marker, Yes/No. When "Yes" is selected, the

side bout marker will make a track in the centre of the previous furrow if this furrow was tram-
lined.

22

BioDrill seed hopper, Yes/No

«
...
46
47
48
49
50
...
»

Содержание Rapid RDA 400S















































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: Cambro Страницы: 6

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: h/p/cosmos Страницы: 81

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Raymarine Страницы: 124

Бренд: Raymarine Страницы: 192

Бренд: Malekko Страницы: 2

Бренд: Major Страницы: 26

Бренд: KCI Страницы: 2

Бренд: KCI Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды