Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 90

Страница: 90 / 110

Troubleshooting

Ver.3 29.06.2007

The drill is sinking, i.e. it drills

deeper than the set drilling

depth!

- Is the O-ring on the master ram's cut-off valve dam-

aged or missing? See

”4.14 Changing the valve seals

on the lifting ram” on page 78.

- Does the stop bolt touch the bottom at the rod's upper

end? In this case the spring has been compressed or is
damaged.

The discs do not rotate properly!

- Are the seed boxes exposed to undue stress? The seed

boxes should sit very lightly.

- Is the soil very soft? It may be necessary to compact

the soil using a roller.

- Is the sowing depth too shallow?

- Have the seed boxes been installed too low? The discs

afford better traction if the seed boxes are raised one
notch.

- Are discs excessively worn?

- Does the soil surface contain a lot of plant scrubs?

- Are the tines of the front implement set too hard re-

sulting in soil that is too loose?

The drill does not place seed at

the bottom of the furrow!

- Are the seed boxes excessively worn?

- Are the seed boxes set one notch too high? The drill

will place the seed more precisely if the boxes are set
low. This does not normally need to be changed for
different soil types.

Irregular fan speed (hydraulic

feed output)!

- Replace the hydraulic filter.

Irregular output seed amount

(hydraulic feed output)!

- Replace the proportional valve in the fan unit.

Содержание Rapid RDA 400S















































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Инструкция по эксплуатации

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды