Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 47

Страница: 47 / 110

RDA 400-450 S

Ver.3 29.06.2007

2.21.3

Programming

The Control Station has been preset at the Väderstad factory depending on the type and size of the
machine it is supplied with. The Control Station settings need to be reentered after replacement or
a reset.

It is also possible to use the settings to adjust e.g., alarm delays, area metering, etc.

To enter the programming menu, keep

pressed while simultaneously switching on the pow-

er switch (1).

If the Control Station already has been switched on, switch to the programming menu by keeping

the button

depressed for 5 seconds. To complete programming and return to the drive

mode, select the last menu in the scroll list:

. Confirm with

Use the selection dial to select the desired menu. Selections are shown against a dark background.

Use

to confirm a selection and then select or change the value of the selected item. Confirm

the value/selection with

Menus:

Language. Select the desired language for alarm texts, etc.

Machine type. Select “RDA 4-450 S”.

Hydraulic feeding, Yes/No.

GPS, Yes/no. See ”

2.21.6 GPS (Global Positioning System)” on page 50

Number of pulses per revolution generated by the seed box drive sensor. Default setting:

360. (Only applies to hydraulic feed output)

Serial number. Record the serial number of the machine here. Select digits with the dial

and advance using

Machine width. Set the machine width here: 4.0 or 4.5 m.

Manual start. Select the intended drive speed here by keeping the button

de-

pressed. (Starting of feed output when drilling is commenced from a corner of the field, etc.;
only for hydraulic feed output.)

Output stop, Yes/No. Option Default setting: No.

Only if Yes has been selected in menu 9, Setting of lift time delay. Default setting 0.0

sec.

Содержание Rapid RDA 400S















































































































Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды

Vaderstad Rapid RDA 400S, Инструкция по эксплуатации

Результаты поиска

Содержание Rapid RDA 400S

Отзывы:

Похожие инструкции для Rapid RDA 400S

Бренды по названию

Популярные бренды