Vaderstad Rapid RDA 400S Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 110

background image

RDA 400-450 S

Ver.3 29.06.2007

55

2.22 Tramlining

2.22.1

Adjusting track width

Figure 2.62

The Rapid drill is usually supplied with the row shutoff and track width specified by the customer.
However, it is possible to change these if necessary:

!

A different track width can be obtained by shifting the feed hoses to the seed coulters.

Example:

A track width of 1.75 m can be increased to 2.0 m by moving the front left and rear

right one step outwards. A track width of 1.5 can be produced by moving the rear left and the fore
right one step inward (Y). For bigger changes in track width, it may be necessary to move the hos-
es inside the hopper instead.

2.22.2

Adjusting row shutoff

Figure 2.63

Tramlining can be done with 1, 2 or 3 row shutoff.

!

The sowing row shutoff can be altered by exchanging the spring under the distributor head for
an operating spring (417772, 417776) or a parking spring (417795) depending on whether
more or less rows are to be shut off.

Table 2.5 Possible track widths

One row shutoff

Two row shutoff

Three row shut-off

C-C 138 cm

C-C 150 cm

-

C-C 163 cm

C-C 175 cm

C-C 163 cm

C-C 188 cm

C-C 200 cm

C-C 188 cm

C-C 213 cm

C-C 225 cm

C-C 213 cm

C-C 238 cm

C-C 250 cm

-

417766, 400 S

417795

417770, 450 S

«
...
53
54
55
56
57
...
»

Содержание Rapid RDA 400S















































































































Отзывы:

Нет отзывов

Похожие инструкции для Rapid RDA 400S

FX-ARM CONTROLLER

Бренд: Magicfx Страницы: 16

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: Rain Bird Страницы: 2

Бренд: Balanced Body Страницы: 4

WJHD100 - DIGITAL DISC RECORDE

Бренд: Panasonic Страницы: 7

Бренд: Bahco Страницы: 9

Бренд: ACCU-CHECK Страницы: 104

Бренд: Rapid Technic Страницы: 152

Бренд: ECE Страницы: 2

Бренд: Ecco Страницы: 5

Evolution Series

Бренд: Bakare Страницы: 38

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды