Ulvac HELIOT 301 Скачать руководство пользователя страница 58

Страница: 58 / 96

- 48 -

4-8-2 List of error messages

Error No.

Error message

Trouble symptom

**** Caution 1 ****

Fore pump trip

The fore pump (GHD-030) has stopped and cannot be started.

**** Caution 2 ****

Main pump trip

The main pump (TMH063-003-002) has stopped and cannot be started.

**** Caution 3 ****

Fil. burn out

Both filaments 1 and 2 have burnt out.
Emission current cannot be obtained due to deterioration or
contamination of the filament.

**** Caution 4 ****

Pig. failure

The Pirani gauge sensor head has burnt out.

**** Caution 5 ****

Ext. power trip

The external power supply has tripped.

**** Notice 1 ****

Error

Action cannot be executed for the setting.

**** Notice 2 ****

F. flow invalid

Fine leak flow cannot be executed.
(Pressure does not lower, pressure fault has occurred.)

**** Notice 3 ****

M. flow invalid

Middle leak flow cannot be executed.
(Pressure does not lower, pressure fault has occurred.)

**** Notice 4 ****

G. flow invalid

Gross leak flow cannot be executed.
(Pressure does not lower, pressure fault has occurred.)

**** Notice 5 ****

Evacuation fault

Roughing is not completed within three minutes.

**** Notice 6 ****

Sen. fault

Sensitivity fault has occurred.

**** Notice 7 ****

Fil. switched

Filament 1 or 2 has burnt out and was changed to the other.

**** Notice 8 ****

Zero fault

Zero adjustment cannot be made at startup.

RS-232C Error

Communication error of program data.

* Refer to "6. INSPECTION & MAINTENANCE" and "7. TROUBLESHOOTING" for

inspection, maintenance and replacement of parts regarding error messages.

Содержание HELIOT 301

































































































Результаты поиска

Содержание HELIOT 301

Отзывы:

Похожие инструкции для HELIOT 301

Бренды по названию

Популярные бренды

Ulvac HELIOT 301, Инструкция по эксплуатации

Результаты поиска

Содержание HELIOT 301

Отзывы:

Похожие инструкции для HELIOT 301

Бренды по названию

Популярные бренды