manualshive.com logo in svg

Ulvac HELIOT 301, Инструкция по эксплуатации, Страница: 5 / 96

Поделиться
Скачать
Ulvac HELIOT 301 Скачать руководство пользователя страница 5

 

 

!

 

CAUTION

Quick start 

Quick start starts the instrument by utilizing the sensitivity data used the 
last time, as it is, independently of the current state of HELIOT. 
Therefore, the measurement error can be great in some cases. 
To ensure test data reliability, it is recommended to start up the instrument 
by normal start. 
It is to be understood that the reliability of leak test when the instrument is 
started by quick start (direct reading of leak rate, etc.) is not warranted.

 

!

 

CAUTION

Test port 

Check that a blank flange or a test object is securely connected to the test 
port. 
If test is made without connecting a blank flange or a test object securely, 
not only measurement will be adversely affected, but also the life of parts 
will be extremely shortened, causing damage to the equipment.

 

!

 

CAUTION

Shutdown 

To shut down the instrument, set up the stop mode in the test mode standby 
status for automatic shutdown. 

!

 

CAUTION

During test 

When test is going on, do not remove the blank flange or test object from 
the test port or vent the test port to atmospheric pressure by other method 
than operation of the controller.    The equipment can be damaged. 

!

 

CAUTION

Venting the test port

 

Before venting, do not remove the blank flange or test object from the test 
port nor vent the test port to atmospheric pressure by other method than 
operation of the controller.    The equipment can be damaged. 

!

 

CAUTION

Main power OFF 

When stop operation is being performed, the message "Please wait" is 
displayed on the LCD.    At this time, do not turn OFF the main power. 
Then the display changes to "Push START".    Turn OFF the main power 
after verifying this message is displayed.

 

!

 

CAUTION

After shutdown 

Do not give vibration or impact to the instrument for about five minutes 
after completion of shutdown operation. 
The equipment can be damaged.

 

!

 

CAUTION

Main power OFF 

Be sure to turn OFF the main power after completion of shutdown 
operation. 

!

 

CAUTION

Error 

If error occurs, reset the error mode after verifying the symptom by the 
message. 
Conduct inspection and repair referring to "Troubleshooting".

 

!

 

CAUTION

Check before startup 

Check again that all preliminary operations above, including installation, 
DIP switch setting, SEN. switch setting and controller setting, etc., have 
been properly completed. 
If there is any fault or problem, not only the instrument may malfunction, 
but also it may be damaged.

 

 

Содержание HELIOT 301

































































































Отзывы:

Нет отзывов