Ulvac HELIOT 301 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 96

background image

Safety Cautions

!

CAUTION

Turn OFF power

Before removing the external panel for inspection or part replacement, shut
off the primary power on the switchboard and disconnect the power cable
from HELIOT.
High voltage is present in HELIOT and can cause danger to human body
by electric shock and damage the equipment.

!

CAUTION

Complete stop

The compound molecular pump rotates at a high speed for about five
minutes after it is stopped.
Before inspection or part replacement, wait for more than five minutes
after the pump has stopped.
Otherwise, you may be injured or the equipment may be damaged.

!

CAUTION

Analyzer tube at high temperature

The area around the analyzer tube and ion source is very hot immediately
after it is deactivated. Before inspection or part replacement, wait for
more than five minutes after deactivating it and carry out work carefully.
Otherwise, you may get burned or the equipment may be damaged.

!

CAUTION

Solenoid valve at high temperature

The coil section of the solenoid valve is very hot immediately after it is
deactivated.
Before inspection or part replacement, wait for more than five minutes
after deactivating it and carry out work carefully.
Otherwise, you may get burned or the equipment may be damaged.

!

CAUTION

Rotary pump at high temperature

The rotary pump is very hot immediately after it is stopped.
Before inspection or part replacement, wait for more than five minutes
after deactivating it and carry out work carefully.
Otherwise, you may get burned or the equipment may be damaged.

!

CAUTION

Turn OFF power

Before installing the instrument, turn off the main power switch and
disconnect the power plug.

!

CAUTION

Turn OFF power

Ground the instrument to prevent earth leakage.

!

CAUTION

Inspection and repair

Before inspection or repair, wait for more than five minutes after stopping
the instrument.
Otherwise, you may be injured or the equipment may be damaged.

!

CAUTION

Hold horizontal

Do not tilt the instrument more than 30 degrees when unpacking or when
moving the instrument, and hold it in a horizontal position when installing
it. Otherwise, oil leak or damage to the equipment may result.

!

CAUTION

Overhaul

The instrument contains parts that are subject to aging, including
consumables (O-rings and drive parts).
Be sure to conduct overhaul to maintain performance once a year.

«
1
2
3
4
5
...
»

Содержание HELIOT 301

































































































Отзывы:

Нет отзывов

Похожие инструкции для HELIOT 301

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

MoistureFinder Compact

Бренд: LaserLine Страницы: 56

LaserRange-Master Gi7 Pro

Бренд: LaserLiner Страницы: 56

Бренд: Laser Tools Страницы: 4

SmartVision-Laser

Бренд: LaserLiner Страницы: 56

Бренд: Narvitech Страницы: 2

Бренд: National Instruments Страницы: 15

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: TA Instruments Страницы: 7

Бренд: Underground Magnetics Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды