Ultima HT18/36 Скачать руководство пользователя страница 3

Страница: 3 / 52

Thank you for choosing Dura Access Control Equipment (DACE). We welcome you to the ever growing community

of happy DACE product owners. The advanced engineering and high-quality construc2on of each DACE product

we build is something of which we are proud.

The Ul2ma gate operator is packed with features to bring you more convenience and to enhance your security.

Your owners manual will introduce you to the features and opera2on of your new Ul2ma gate operator. It is sug-

gested that you read it carefully since the informa2on it contains can contribute greatly to the sa2sfac2on you

receive from your new gate operator.

We also recommend that you follow the maintenance schedule so that your operator will give you many years of

problem free service.

Please keep this manual in a safe, convenient place so that you can refer to it from 2me to 2me when performing

maintenance or ac2va2ng new features.

Look out for these icons in the instrucon manual:

Take Careful Note!

Informa2on that may aﬀect the operator or func2on in a way you did not expect. .

Good Idea!

Following this instruc2on might assist in the future or help with the installa2on.

Warning!

Informa2on about poten2al hazard/s & detail requiring your special aGen2on.

Please a0ach your invoice to this manual for future use (see warranty).

Please read the maintenance schedule for your Ulma operator to ensure its longevity and connuous safe operaon.

Alterna2ng Current (pertaining to a supply voltage)

Auto Close (pertaining to the gate moving)

BAC

Beams Auto Close (Same as PIRAC)

DACE

Dura Access Control Equipment

Direct Current

DIY

Do It Yourself

E.C.A

Electrical Contractors Associa2on

FRX

Free Exit

HID

Human Interface Device (Joys2ck / Speaker / Display)

Infrared

IRBC

Closing Infrared Beam (Safety Beam)

IRBO

Opening Infrared Beam (Safety Beam)

LCD

Liquid Crystal Display

LED

Light Emi?ng Diode (Indicator light)

Mag

Magne2c

NAV

Naviga2on

PED

Pedestrian

PIRAC

Passive Infrared Auto Close (Same as BAC)

RSSI

Receiver Signal Strength Indicator

Receiver (or onboard receiver)

Trig

Trigger

TransmiGer

ABBREVIATIONS

FOREWORD

Содержание HT18/36





















































Результаты поиска

Содержание HT18/36

Отзывы:

Похожие инструкции для HT18/36

Бренды по названию

Популярные бренды

Ultima HT18/36, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HT18/36

Отзывы:

Похожие инструкции для HT18/36

Бренды по названию

Популярные бренды