Ultima HT18/36 Скачать руководство пользователя страница 11

Страница: 11 / 52

I. Lay a concrete slab 400mm x 400mm x 200mm:

•

Dig a hole and place the conduit ❶ in the correct

posi2on.

•

Fill the hole with concrete & allow to set.

II. Place the founda2on plate on the concrete slab &

feed the conduit through the cable inlets ❷.

III. Ensure a 23mm clearance between the inner

edge of the founda2on plate and the edge of the

gate. This measurement is based on DACE rack.

See below to calculate clearance if using other

rack.

IV. AGach the founda2on plate to the slab using four

8mm anchors ❸.

ANCHORING THE FOUNDATION PLATE

Open the ‘manual release door’ and pull the

release pin un2l the lid is free. The Lid can now

be removed.

REMOVING THE LID

1. Open the ‘manual release door’ and rotate the thumb

wheel clockwise, just un2l the gate begins to move.

2. The thumb wheel must not be allowed to rotate too far.

3. To re-engage the gearbox, rotate the thumb wheel

counter clockwise while pushing on the gate un2l you

hear a click in the gearbox.

4. Do not rotate the thumb wheel any further aLer hearing

the gearbox click.

PLACING THE OPERATOR IN MANUAL OVERRIDE

To calculate the clearance required between the edge of the
founda2on plate and the edge of the gate (A), measure the
width of the rack (B) and minus 9.

eg. If the width of the rack is 32mm less 9 = 23. Thus the
clearance required is 23mm

Side view

Gate

Rack

Founda2on

Plate

Содержание HT18/36





















































Результаты поиска

Содержание HT18/36

Отзывы:

Похожие инструкции для HT18/36

Бренды по названию

Популярные бренды

Ultima HT18/36, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HT18/36

Отзывы:

Похожие инструкции для HT18/36

Бренды по названию

Популярные бренды