Ublox MAX-M10 страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 92

background image

MAX-M10M - Integration manual

3.6.2.3 Cyclic tracking

Power save mode cyclic tracking (PSMCT) operation is described in

.

PSMCT supports 1 Hz and 2 Hz navigation update rates. In addition, longer update periods from
2 s to 10 s are supported at 1 s steps.

Figure 13: Cyclic tracking operation

• When the receiver is switched on, it ﬁrst enters the "Acquisition" state. A larger number of

signals tracked later helps the receiver to remain in the "POT" state if some signals get blocked
and are lost. This may reduce the overall power consumption.

• If the receiver is able to acquire a valid position ﬁx (one passing the navigation output ﬁlters)

within the time given by the

Acquisition timeout

, it switches to the "Tracking" state and the

ONTIME starts. Otherwise it enters the "Inactive for search" state and restarts after the
conﬁgured search period (minus a start-up margin).

• Once the ONTIME is over, the "POT" state is entered. Setting the ONTIME to zero causes the

receiver to enter the "POT" state as soon as possible.

• In the "POT" state the receiver continues to output position ﬁxes according to the CFG-RATE-*.
• If the signal becomes weak or is lost during the "POT" state, the "Tracking" state is entered.
• Once the signal is good again and the newly started ONTIME is over, the receiver will re-enter

the "POT" state.

• If the receiver cannot get a position ﬁx in the "Tracking" state, it enters the "Acquisition"

state. Should the acquisition fail as well, the "Inactive for search" state is entered. If
DONOTENTEROFF is enabled and no ﬁx is possible, the receiver will remain in the "Acquisition"
state until a ﬁx is possible and it will never enter the "Inactive for search" state.

3.6.2.4 On/Oﬀ mode

Power save mode on-oﬀ (PSMOO) operation is described in

PSMOO requires an RTC to maintain time.

Figure 14: On/oﬀ mode operation

• When the receiver is switched on, it ﬁrst enters the "Acquisition" state.
• If it is able to acquire a valid position ﬁx (one passing the navigation output ﬁlters) within the

time given by the

Acquisition timeout

, it switches to the "Tracking" state and the ONTIME

UBX-22038241 - R02

3 Receiver functionality

Page 38 of 92

C1-Public

«
...
36
37
38
39
40
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: EA Страницы: 24

Бренд: UNITED Страницы: 22

Бренд: janitza Страницы: 58

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: Parker Страницы: 4

Бренд: National Instruments Страницы: 14

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Бренд: AC Tech Страницы: 2

Бренд: V-TAC Страницы: 2

Бренд: Diamond Systems Страницы: 15

Бренд: D+H Страницы: 36

Бренд: netvox Страницы: 12

Security Center AZ5140

Бренд: Abus Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды