Ublox MAX-M10 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 92

Ublox MAX-M10 Скачать руководство пользователя страница 14

MAX-M10M - Integration manual

rate. This supports the high performance navigation update rate with minor increase in power
consumption.

For the high navigation update rates, increase the communication speed and reduce the number
of enabled messages.

The high performance navigation update rate can be conﬁgured in the device's one-time
programmable (OTP) memory. The OTP conﬁguration is only done once, and is subsequently applied
automatically at every startup. The conﬁguration string for setting the high CPU clock rate in the
OTP memory is given in

. This occupies 18 bytes of OTP memory space.

Changes made in the OTP conﬁguration are permanent and cannot be reverted.

CPU clock

Conﬁguration string

Default CPU clock

Default

High CPU clock

B5 62 06 41 10 00 03 00 04 1F 54 5E 79 BF 28 EF 12 05 FD FF FF FF 8F 0D B5 62 06 41 1C
00 04 01 A4 10 BD 34 F9 12 28 EF 12 05 05 00 A4 40 00 B0 71 0B 0A 00 A4 40 00 D8 B8
05 DE AE

Table 6: High performance navigation update rate conﬁguration in OTP memory

To conﬁgure the high performance navigation update rate in OTP memory:

1.

Power up the device.

2.

Test the communication interface by polling the UBX-MON-VER message.

3.

Send the conﬁguration string provided in

. The device returns two UBX-ACK-ACK

messages with sequence of bytes B5 62 05 01 02 00 06 41 4F 78.

4.

Set the device reset to a hardware reset. Power the device oﬀ and on or send the UBX-CFG-RST
message to the device. The higher clock setting is applied at startup.

5.

To verify that the conﬁguration item is correctly set,

• send the following sequence to the receiver: B5 62 06 8B 14 00 00 04 00 00 01 00 A4 40 03

00 A4 40 05 00 A4 40 0A 00 A4 40 4C 15

• receive a UBX-CFG-VALGET message with the following sequence: B5 62 06 8B 24 00 01 04

00 00 01 00 A4 40 00 B0 71 0B 03 00 A4 40 00 B0 71 0B 05 00 A4 40 00 B0 71 0B 0A 00
A4 40 00 D8 B8 05 76 81

• receive a UBX-ACK-ACK message with the following sequence: B5 62 05 01 02 00 06 8B 99

C2

6.

The OTP memory conﬁguration is completed and veriﬁed.

2.2 Navigation conﬁguration

This section presents various conﬁguration options related to the navigation engine. These options
can be conﬁgured through CFG-NAVSPG-* conﬁguration keys.

2.2.1 Dynamic platform

The dynamic platform model can be conﬁgured through the CFG-NAVSPG-DYNMODEL
conﬁguration item. For the supported dynamic platform models and their details, see

and

.

Platform

Description

Portable

Applications with low acceleration, e.g. portable devices. Suitable for most situations.

Stationary

Used in timing applications (antenna must be stationary) or other stationary applications.
Velocity restricted to 0 m/s. Zero dynamics assumed.

UBX-22038241 - R02

2 Receiver conﬁguration

Page 14 of 92

C1-Public

«
...
12
13
14
15
16
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды