manualshive.com logo in svg

Ublox MAX-M10, Руководство по интеграции

Поделиться
Скачать
Ublox MAX-M10 Скачать руководство пользователя страница 13

MAX-M10M - Integration manual

Configuration item

Description

Comments

CFG-HW-ANT_CFG_OPENDET

Enable open circuit detection

CFG-HW-ANT_CFG_OPENDET_POL

Open antenna detection polarity

Set to 1 if the required logic polarity is
active-low (default).

CFG-HW-ANT_CFG_PWRDOWN

Power down antenna supply if short
circuit is detected

Requires CFG-HW-
ANT_CFG_VOLTCTRL and CFG-HW-
ANT_CFG_SHORTDET to be enabled.

CFG-HW-ANT_CFG_PWRDOWN_POL Power down antenna logic polarity

Set to 1 if the required logic polarity is
active-high (default).

CFG-HW-ANT_CFG_RECOVER

Enable auto-recovery in the event of a
short circuit

To use this feature, enable short
circuit detection and CFG-HW-
ANT_CFG_PWRDOWN.

CFG-HW-ANT_SUP_SWITCH_PIN

PIO number of the pin used for switching
antenna supply

PIO5 is recommended if available. This
pin can be used as an LNA_EN signal
to control an external LNA, especially
if software standby mode or power
save mode on/off (PSMOO) operation is
used.

CFG-HW-ANT_SUP_SHORT_PIN

PIO number of the pin used for detecting
a short circuit in the antenna supply

UART or I2C pins can be used for the
short detection, depending on which
interface is used for communication.

CFG-HW-ANT_SUP_OPEN_PIN

PIO number of the pin used for detecting
open/disconnected antenna

UART or I2C pins can be used for the
short detection, depending on which
interface is used for communication.

Table 4: Antenna supervisor configuration

It is possible to obtain the status of the antenna supervisor from the UBX-MON-RF message. Refer
to the interface manual for the description of the 

antStatus

 and 

antPower

 fields [

3

]. In addition, any

changes in the status of the antenna supervisor are reported to the host interface as ANTSTATUS
in NMEA notice messages.

ANTSTATUS

Description

OFF

Antenna is off

ON

Antenna is on

DONTKNOW

Antenna power status is not known

Table 5: Antenna power status

2.1.7 High performance navigation update rate configuration

The navigation update rate is a GNSS configuration item which determines how many position fixes
the receiver calculates and outputs per second. The maximum achievable navigation update rate
depends on the number of GNSS signals the receiver is tracking. Depending on the geographical
location  and  GNSS  constellations  enabled,  the  number  of  tracking  channels  in  use  may  vary.  In
particular,  in  Asia  there  is  a  large  number  of  BeiDou  satellites  available  potentially  limiting  the
maximum  achievable  navigation  update  rate.  In  regions  with  a  lower  number  of  available  BeiDou
satellites, a higher navigation rate is achieved.

The  maximum  navigation  update  rate  given  in  the  datasheet  is  provided  for  a  minimum  of  98%
position  fix  rate,  i.e.,  up  to  2%  position  fixes  can  get  lost  in  case  of  high  availability  of  signals.
The navigation update rate can be increased beyond the maximum value stated in the datasheet.
However, this may result in a reduced fix rate if a very large number of satellites is tracked.

u-blox M10 devices are optimized for low power consumption and come with the default CPU clock
rate that supports the default navigation update rate stated in the product datasheet. However, it
is possible to achieve a higher navigation update rate by configuring the device for a higher clock

UBX-22038241 - R02

 

2 Receiver configuration

Page 13 of 92

C1-Public

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды