Ublox MAX-M10 Скачать руководство пользователя | Manualshive

Страница: 66 / 92

background image

MAX-M10M - Integration manual

Figure 23: VCC and V_IO supplied by separate supplies, and external power supply at V_BCKP

Figure 24: VCC and V_IO supplied by separate supplies. No external power supply at V_BCKP.

4.2 RF interference

The received GNSS signal power at the antenna is very low compared to other wireless
communication signals. The nominal -130 dBm received GNSS signal strength is below the thermal
noise ﬂoor, making a GNSS receiver susceptible to interference from nearby RF sources of any kind.

As an example, cellular applications emit signals with power levels of approxi30 dBm, while
the GNSS signal is less than -128 dBm when reaching the antenna. By simply comparing these
numbers it is obvious that interference issues must be seriously considered during the design
phase.

4.2.1 In-band interference

Although the radio communications standards prevent intentional RF signal sources from
interfering the GNSS frequencies, many devices emit RF power into the GNSS band at levels much
higher than the GNSS signal itself.

One  reason  is  that  the  frequency  band  above  1  GHz  is  not  well  regulated  with  regards  to  EMI,
and  even  if  permitted,  signal  levels  are  much  higher  than  the  GNSS  signal  power.  In  particular,
all  types  of  digital  equipment,  such  as  PCs,  digital  cameras,  LCD  screens,  etc.  tend  to  emit  a
broad frequency spectrum up to several GHz of frequency. Also wireless transmitters may generate
spurious emissions that fall into the GNSS band.

The section deﬁnes measures against in-band interference during the design phase of the
application.

4.2.2 Out-of-band interference

Out-of-band interference is caused by signal frequencies that are diﬀerent from the GNSS carrier
frequency. The main sources are wireless communication systems such as LTE, GSM, CDMA,
WCDMA, Wi-Fi, BT, etc. Typically, these systems may emit their speciﬁed maximum transmit power
in close proximity to the GNSS receiving antenna, especially if such a system is integrated with
the GNSS receiver. Even at reasonable antenna selectivity, destructive power levels may reach the
RF input of the GNSS receiver. In addition, larger signal interferers may generate intermodulation

UBX-22038241 - R02

4 Hardware integration

Page 66 of 92

C1-Public

«
...
64
65
66
67
68
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: UNITED Страницы: 8

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: Haes Страницы: 42

TBEN-L 8IOL Series

Бренд: turck Страницы: 148

APEXpy 07-37A2-2111/ 520Series

Бренд: Bartec Страницы: 98

Бренд: Quickie Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды