Ublox MAX-M10 страница 31 Скачать руководство пользователя

Страница: 31 / 92

MAX-M10M - Integration manual

Part

Description

Current limiter in the event of a short circuit

Table 17: Components in two-pin antenna supervisor

The open drain buﬀer shown in

Figure 11

is not needed if V_ANT is the same voltage level as V_IO.

3.3.1.3 Antenna voltage control - ANT_OFF_N

The antenna voltage control is enabled by default in MAX-M10M with the conﬁguration item CFG-
HW-ANT_CFG_VOLTCTRL set to true (1).

The antenna status (as reported in UBX-MON-RF and UBX-INF-NOTICE messages) is not
reported unless the antenna voltage control has been enabled.

Result:

• UBX-MON-RF: Antenna status = OK. Antenna power status = ON.
• ANT_OFF_N = active low. The pin is pulled high to enable an external antenna or LNA.

Startup message at power-up if the conﬁguration is stored:

$GNTXT,01,01,02,ANTSUPERV=AC *00

$GNTXT,01,01,02,ANTSTATUS=INIT*3B

$GNTXT,01,01,02,ANTSTATUS=OK*25

ANTSUPERV=AC

indicates that antenna control is activated.

3.3.1.4 Antenna short detection - ANT_SHORT_N

Enable the antenna short detection by setting the conﬁguration item CFG-HW-
ANT_CFG_SHORTDET to true (1).

Result:

• UBX-MON-RF: Antenna status = OK. Antenna power status = ON.
• ANT_OFF_N = active low to disable an external antenna. Therefore, the pin is pulled high to

enable an external antenna.

• ANT_SHORT_N = active low to report a short circuit. The pin is default high (PIO pull-up

enabled).

Startup message at power-up if the conﬁguration is stored:

$GNTXT,01,01,02,ANTSUPERV=AC SD *37

$GNTXT,01,01,02,ANTSTATUS=INIT*3B

$GNTXT,01,01,02,ANTSTATUS=OK*25

ANTSUPERV=AC SD

indicates that antenna control and short detection are activated.

If a short circuit is detected in the antenna (ANT_SHORT_N pulled low):

$GNTXT,01,01,02,ANTSTATUS=SHORT*73

• UBX-MON-RF: Antenna status = SHORT. Antenna power status = ON (automatic power-down

is not enabled, CFG-HW-ANT_CFG_PWRDOWN is oﬀ by default).

• ANT_OFF_N = high (external antenna enabled).

UBX-22038241 - R02

3 Receiver functionality

Page 31 of 92

C1-Public

Содержание MAX-M10





























































































Результаты поиска

Содержание MAX-M10

Отзывы:

Похожие инструкции для MAX-M10

Бренды по названию

Популярные бренды

Ublox MAX-M10, Руководство по интеграции

Результаты поиска

Содержание MAX-M10

Отзывы:

Похожие инструкции для MAX-M10

Бренды по названию

Популярные бренды