manualshive.com logo in svg

Ublox MAX-M10, Руководство по интеграции

Поделиться
Скачать
Ublox MAX-M10 Скачать руководство пользователя страница 11

MAX-M10M - Integration manual

It  is  recommended  to  enable  QZSS  L1C/A  when  GPS  L1C/A  is  enabled  in  order  to  mitigate
possible cross-correlation issues between the signals.

Refer  to  the  Interface  description  [

3

]  for  more  information  on  the  CFG-SIGNAL-*  configuration

group.

2.1.3.1 BeiDou B1I and B1C signals

BeiDou B1I and B1C signals differ in terms of the center frequency, bandwidth, and modulation.
Therefore, there are differences in performance and supported GNSS signals and features.

Benefits of using BeiDou B1I signal:

BeiDou B1I offers superior GNSS performance. High start-up sensitivity and fast time-to-first-fix
(TTFF)  enable  acquisition  of  a  large  number  of  BeiDou  satellites.  The  tracking  and  reacquisition
sensitivity for acquired signals is approximately at the same level for BeiDou B1I and B1C.

•

Faster TTFF and higher start-up sensitivity.

 BeiDou B1I signals are acquired significantly

faster and at a lower signal level than BeiDou B1C signals.

•

Better availability.

 Higher start-up sensitivity results in a larger number of BeiDou satellites

tracked and used in navigation solution especially at low signal level.

•

AssistNow Online support.

 Enhanced start-up sensitivity and TTFF.

•

Power save mode (PSM) support.

 PSM cyclic tracking (PSMCT) and on/off (PSMOO) mode

operation are supported.

Benefits of using BeiDou B1C signal:

BeiDou B1C signal has the same center frequency as GPS L1 C/A enabling concurrent use of 4 GNSS
constellations. Multi-GNSS configurations with BeiDou B1C also have a lower power consumption
compared to those with BeiDou B1I.

•

Concurrent reception of 4 GNSS

 with GPS L1 C/A, Galileo E1, BeiDou B1C, and GLONASS L1OF.

•

Lower power consumption.

 No additional frequency band required for BeiDou B1C in multi-

GNSS constellations resulting in a lower power consumption during acquisition and tracking
phases.

2.1.4 Communication interface configuration

Several  configuration  groups  allow  configuring  the  operation  mode  of  the  communication
interfaces. These include parameters for the data framing, transfer rate and enabled input/output
protocols.  See 

Communication  interfaces  and  PIOs

  section  for  details.  The  configuration  groups

available for each interface are:

Interface

Configuration groups

UART

CFG-UART1-*, CFG-UART1INPROT-*, CFG-UART1OUTPROT-*

I2C

CFG-I2C-*, CFG-I2CINPROT-*, CFG-I2COUTPROT-*, CFG-TXREADY-*

Table 3: Interface configuration

The  UART  baudrate  in  MAX-M10M  is  configured  to  9600  baud  which  is  different  to  the
firmware default. This ensures backwards compatibility with previous generations of u-blox MAX
modules.

2.1.5 Message output configuration

The receiver supports two protocols for output messages: industry-standard NMEA and u-blox UBX.
Any message type can be enabled or disabled individually and the output rate is configurable.

UBX-22038241 - R02

 

2 Receiver configuration

Page 11 of 92

C1-Public

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды