Ublox MAX-M10 страница 59 Скачать руководство пользователя | Manualshive

Страница: 59 / 92

background image

MAX-M10M - Integration manual

• The

AssistNow Autonomous

subsystem automatically invalidates data that has become too old

and that would introduce unacceptable positioning errors. This threshold is conﬁgurable.

• The prediction quality will be automatically improved if the satellite has been observed multiple

times. However, this requires the availability of a suitable ﬂash memory. Improved prediction
quality also extends the maximum usability period of the data.

•

AssistNow Autonomous

considers GPS, GLONASS, Galileo and BeiDou satellites only. It will not

consider satellites on orbits with an eccentricity of >0.05 (e.g., Galileo E18). For GLONASS
support, a suitable ﬂash memory is mandatory because a single GLONASS broadcast
ephemeris contains information only for approximately 30 minutes. This is not long enough
to extend it in a usable way. Orbit information of each GLONASS satellite must be collected at
least for four hours to generate data.

3.12.4.2 Interface

Several UBX protocol messages provide interfaces to the

AssistNow Autonomous

feature:

• The CFG-ANA-USE_ANA item is used to enable or disable the

AssistNow Autonomous

feature.

When enabled, the receiver will automatically produce

AssistNow Autonomous

data for newly

received broadcast ephemerides and, if that data is available, automatically provide the
navigation subsystem with orbits when necessary and adequate.

• The CFG-ANA-* conﬁguration group also allows for a conﬁguration of the maximum acceptable

orbit error. See the next section for an explanation of this feature. It is recommended to use the
ﬁrmware default value that corresponds to a default orbit data validity of approximately three
days (for GPS satellites observed once) and up to six days (for GPS and GLONASS satellites
observed multiple times over a period of at least half a day).

If the receiver uses ﬂash memory, disabling the

AssistNow Autonomous

feature will delete all

previously collected satellite observation data from the ﬂash memory.

• The UBX-NAV-AOPSTATUS message provides information on the current state of the

AssistNow Autonomous

subsystem. The status indicates whether the

AssistNow Autonomous

subsystem is currently idle (or not enabled) or busy generating data or orbits. Hosts should

UBX-22038241 - R02

3 Receiver functionality

Page 59 of 92

C1-Public

«
...
57
58
59
60
61
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: Echelon Страницы: 40

Бренд: Jetline Страницы: 58

Бренд: Eaton Страницы: 28

Бренд: Parallel Страницы: 16

Бренд: V2 Страницы: 46

Бренд: Garmin Страницы: 4

Бренд: Gascat Страницы: 32

Бренд: Saluki Страницы: 13

Бренд: Parker Страницы: 4

Бренд: Mitsubishi Страницы: 16

Бренд: SOMFY Страницы: 4

Бренд: Procom Страницы: 10

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Bardiani Valvole Страницы: 24

Бренд: Pfeiffer Vacuum Страницы: 100

VARIOMATIC SARV 07.1

Бренд: AUMA Страницы: 32

Бренд: Z-Wave Страницы: 44

HydroGuard 1430 Series

Бренд: Powers Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды