Ublox MAX-M10 страница 19 Скачать руководство пользователя | Manualshive

Страница: 19 / 92

background image

MAX-M10M - Integration manual

Figure 5: Flowchart of course over ground freezing

2.2.7 Super-Signal (Super-S) technology

In normal operating conditions, low signal strength (that is, signal attenuation) indicates possible
degradation due to multi-path. The receiver trusts such signals less in order to preserve the
quality of the position solution in poor signal environments. This feature can result in degraded
performance in situations where the signals are attenuated for another reason, for example due
to antenna placement. In this case, the weak signal compensation feature can be used to restore
normal performance. There are three possible modes:

• Disabled: no weak signal compensation is performed
• Automatic: the receiver automatically estimates and compensates for the weak signal
• Conﬁgured: the receiver compensates for the weak signal based on a conﬁgured value

These modes can be selected using CFG-NAVSPG-SIGATTCOMP. In the case of the "conﬁgured"
mode, the user should input the maximum C/N0 observed in a clear-sky environment, excluding any
outliers or unusually high values. Choose the conﬁgured value carefully, as it can have a large impact
on the receiver performance.

2.3 OTP memory conﬁguration

MAX-M10M contains a one-time programmable (OTP) memory. This is a non-volatile memory for
storing conﬁguration settings and ROM patches permanently in the device. The stored data cannot
be modiﬁed after it has been initially programmed. The device applies the settings and ROM patches
on the device startup.

As the space in the OTP memory is limited, only essential system conﬁguration settings should be
stored. The total space used for device conﬁguration and ROM patches in the OTP memory must
not exceed 74 bytes. Other settings can be stored in the BBR or sent from the host to the device
on each device startup.

Ensure that the ﬁnal conﬁguration stored and optional ROM patches do not require more than
74 bytes of OTP memory space.

UBX-22038241 - R02

2 Receiver conﬁguration

Page 19 of 92

C1-Public

«
...
17
18
19
20
21
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: Eaton Страницы: 16

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: Campbell Страницы: 8

Бренд: Laars Страницы: 28

Бренд: Samson Страницы: 48

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренд: K&K Страницы: 6

Бренд: Omnex Страницы: 9

Бренд: Omegon Страницы: 6

Бренд: WATERLOO Страницы: 8

Бренд: York Страницы: 20

FX-COMM4NDER MFX3203

Бренд: Magicfx Страницы: 16

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

Saxun Mosquito Screen Lateral Door 2020

Бренд: Gimenez Ganga Страницы: 2

Бренд: Keysight Technologies Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды