Ublox MAX-M10 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 92

Ublox MAX-M10 Скачать руководство пользователя страница 62

MAX-M10M - Integration manual

detailed information about the position ﬁxes. However, enabling the EXTRAPVT and EXTRAODO
ﬂags reduces the number of ﬁxes that can be batched.

The receiver will reject the conﬁguration if it cannot allocate the required buﬀer memory. To ensure
robust operation of the receiver the limits in

are enforced:

EXTRAPVT

EXTRAODO

Maximum number of epochs

0

0

600

0

1

443

1

0

309

1

1

261

Table 29: Maximum number of batched epochs

It is recommended to disable all periodic output messages when using data batching. This
improves system robustness and also helps ensure that the output of batched data is not
delayed by other messages.

The buﬀer size is set up in terms of navigation epochs. This means that the time that can be
covered with a certain buﬀer depends on the navigation rate. This rate can be set via the "CFG-
RATE-" conﬁguration group.

3.13.3 Retrieval

UBX-LOG-RETRIEVEBATCH message starts the process which allows the receiver to output batch
entries. Batching must not be stopped for readout because all batched data is lost when the feature
is disabled.

Batched ﬁxes are always retrieved starting with the oldest ﬁx in the buﬀer and progressing towards
newer ones. There is no way to skip certain ﬁxes during retrieval.

When a UBX-LOG-RETRIEVEBATCH message is sent the receiver transmits all batched ﬁxes. It is
recommended to send a retrieval request with

sendMonFirst

set. This way the receiver will send

a UBX-MON-BATCH message ﬁrst that contains the number of ﬁxes in the batching buﬀer. This
information can be used to detect when the u-blox receiver ﬁnishes sending data.

Once retrieval has started, the receiver will ﬁrst send UBX-MON-BATCH message if

sendMonFirst

option was selected in the UBX-LOG-RETRIEVEBATCH message. After that, it will send UBX-LOG-
BATCH messages with the batched ﬁxes.

To maximize the speed of transfer, it is recommended that a high communication data rate is used.

The receiver will discard retrieval request while processing a previous UBX-LOG-
RETRIEVEBATCH message.

The receiver does

not

acknowledge the reception of UBX-LOG-RETRIEVEBATCH message. The

receiver responds with UBX-MON-BATCH (optional) and UBX-LOG-BATCH messages.

3.14 CloudLocate

In CloudLocate setup, the host processor of the customer application fetches a set of satellite signal
measurements from the receiver and sends those to the u-blox CloudLocate service for position
calculation. The CloudLocate service uses these measurements and current assistance data to
calculate the receiver position. This data is then provided to the customer enterprise cloud for
further use. Power saving up to 90% is possible compared to a cold start scenario.

UBX-22038241 - R02

3 Receiver functionality

Page 62 of 92

C1-Public

«
...
60
61
62
63
64
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды