Ublox MAX-M10 Скачать руководство пользователя

Страница: 4 / 92

MAX-M10M - Integration manual

3.8 Time mark..................................................................................................................... 47
3.9 Time pulse..................................................................................................................... 48

3.9.1 Recommendations.......................................................................................................................49
3.9.2 Time pulse conﬁguration............................................................................................................50

3.10 Time maintenance....................................................................................................51

3.11 Protection level......................................................................................................... 52

3.11.1 Introduction.................................................................................................................................52
3.11.2 Interface.......................................................................................................................................53
3.11.3 Expected behavior..................................................................................................................... 54

3.12 Multiple GNSS assistance (MGA)....................................................................... 54

3.13 Data batching............................................................................................................ 61

3.13.1 Introduction.................................................................................................................................61
3.13.2 Setting up the data batching................................................................................................. 61
3.13.3 Retrieval....................................................................................................................................... 62

3.14 CloudLocate................................................................................................................62

3.14.1 CloudLocate measurements................................................................................................... 63

4 Hardware integration......................................................................................................... 64

4.1 Power supply..........................................................................................................................................64

4.2 RF interference......................................................................................................................................66

4.2.1 In-band interference.................................................................................................................... 66
4.2.2 Out-of-band interference........................................................................................................... 66
4.2.3 Spectrum analyzer.......................................................................................................................67

4.3 RF front-end...........................................................................................................................................68

4.4 Layout...................................................................................................................................................... 71

4.4.1 Package footprint, copper and solder mask.......................................................................... 72

5 Product handling................................................................................................................. 75

UBX-22038241 - R02

Contents

Page 4 of 92

C1-Public

Содержание MAX-M10





























































































Результаты поиска

Содержание MAX-M10

Отзывы:

Похожие инструкции для MAX-M10

Бренды по названию

Популярные бренды

Ublox MAX-M10, Руководство по интеграции

Результаты поиска

Содержание MAX-M10

Отзывы:

Похожие инструкции для MAX-M10

Бренды по названию

Популярные бренды