Ublox MAX-M10 страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 92

background image

MAX-M10M - Integration manual

If CFG-HW-ANT_CFG_PWRDOWN has been enabled previously (set to true), the polarity of
the ANT_OFF_N signal changes to power down (disable) the antenna supply when a short is
detected.

After  a  detected  antenna  short,  the  reported  antenna  status  continues  to  be  reported  as  a
SHORT.  If  auto-recovery  is  enabled  for  the  antenna  short  detection,  the  antenna  status  can
recover  after  a  timeout  of  60  seconds.  Recovering  the  antenna  status  immediately  requires
either a power cycle or switching the antenna short detection oﬀ and on again.

3.3.1.5 Antenna short detection auto-recovery

Enable the antenna short detection auto-recovery by setting the conﬁguration item CFG-HW-
ANT_CFG_RECOVER to true (1).

To use the auto-recovery feature, enable CFG-HW-ANT_CFG_PWRDOWN which requires CFG-
HW-ANT_CFG_SHORTDET and CFG-HW-ANT_CFG_VOLTCTRL to be enabled.

Result:

• UBX-MON-RF: Antenna status = OK. Antenna power status = ON.
• ANT_OFF_N = active low. The pin is pulled high to enable an external antenna.
• ANT_SHORT_N = active low. The pin is default high (PIO pull-up enabled, to be pulled low if a

SHORT is detected).

Startup message at power-up if the conﬁguration is stored:

$GNTXT,01,01,02,ANTSUPERV=AC SD PDoS SR*3E

$GNTXT,01,01,02,ANTSTATUS=INIT*3B

$GNTXT,01,01,02,ANTSTATUS=OK*25

ANTSUPERV=AC SD PDoS SR

(indicates short circuit recovery added - SR)

If short circuit is detected (ANT_SHORT_N pulled low):

$GNTXT,01,01,02,ANTSTATUS=SHORT*73

• UBX-MON-RF: Antenna status = SHORT. Antenna power status = OFF (automatic power-down

is enabled).

• ANT_OFF_N = low (external antenna disabled).

After a timeout period of 60 seconds, the receiver retests the short circuit condition by enabling the
antenna (i.e. pulling ANT_OFF_N high).

If a short is not present, the receiver reports antenna condition is OK:

$GNTXT,01,01,02,ANTSTATUS=OK*25

UBX-MON-RF: Antenna status = OK. Antenna power status = ON.

3.3.1.6 Antenna open circuit detection - ANT_DETECT

Enable the antenna open circuit detection by setting the conﬁguration item CFG-HW-
ANT_CFG_OPENDET to true (1).

Result:

• UBX-MON-RF: Antenna status = OK. Antenna power status = ON.
• ANT_OFF_N = active low. The pin is pulled high to enable an external antenna.
• ANT_SHORT_N = active low. The pin is default high (PIO pull-up enabled, to be pulled low if a

SHORT is detected).

UBX-22038241 - R02

3 Receiver functionality

Page 32 of 92

C1-Public

«
...
30
31
32
33
34
...
»

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

Бренд: Aalborg Страницы: 128

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: Omnex Страницы: 9

Бренд: Omegon Страницы: 6

Бренд: WATERLOO Страницы: 8

Бренд: Dantherm Страницы: 20

Бренд: Paser Страницы: 2

Бренд: Mitsubishi Страницы: 16

Бренд: FADAL Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

Бренд: CP Electronics Страницы: 12

Бренд: Radio Shack Страницы: 29

Бренд: TAC Страницы: 76

Бренд: FAAC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды