manualshive.com logo in svg

Ublox MAX-M10, Руководство по интеграции

Ublox MAX-M10 - Полное руководство по интеграции продукта доступно для загрузки бесплатно с manualshive.com. Это руководство обязательно поможет вам успешно интегрировать устройство в ваш проект. Не упустите возможность скачать мануал прямо сейчас!

Поделиться
Скачать
background image

MAX-M10M - Integration manual

Feature

Change

Action needed / Remarks

BeiDou B1I

BeiDou satellite IDs up to 63 supported.

-

SBAS

New SBAS PRN selection: 123, 126-129, 131, 133, 136-138.

Code change (optional)

QZSS L1S

SLAS corrections are now applied for navigation.

Code change (optional)

QZSS IMES

Not supported in current firmware.

Code change (optional)

Protocols

NMEA

Supports NMEA V4.11, V4.10, V4.0, V2.3, and V2.1. NMEA V4.11
is enabled by default.
NMEA GSV messages are grouped separately in u-blox M10 as
compared to u-blox M8 in the case of zero signal C/No level. In
M10, if the signal's C/No level is 0, the FW will set the "signal ID"
to zero as an unknown signal for not being able to track them. FW
will then create separate GSV messages, grouping the untracked
signals  with  zero  C/No  and  other  messages  for  grouping  the
tracked  signals  with  non-zero  C/No.  For  the  untracked  signals
message group, the C/No field is marked as empty (i.e. , ,). There
is no configuration to revert this to the u-blox M8 format.

Code change (optional)

RTCM

Not supported in current firmware.

Code change

General

Configuration concept

New configuration scheme using UBX-CFG-VALSET and UBX-
CFG-VALGET messages.

Code change

Navigation update rate

Navigation update rate up to 18 Hz for single GNSS, 10 Hz for 3
GNSS, and 5 Hz for 4 GNSS constellations.

Code change (optional)

Super-S

New feature. Improves performance under weak signal
conditions. Enabled by default in current firmware.

-

Power save mode (PSM)

PSM configuration options have changed:
PSMCT:  4  Hz  navigation  rate  not  supported.  PSMCT  period  is
configured with CFG-RATE configuration group.
BeiDou B1C not supported in power save modes.

Code change (new
configuration messages)

Altitude limit

The maximum altitude limit increased to 80 000 m.

-

Features

AssistNow

Simultaneous operation of AssistNow Online, Offline and
Autonomous. New AssistNow Offline data download options are
available. The time period can be limited to a resolution of days
to reduce the data package size.

Code change (optional)

CloudLocate

New feature. Position calculation in the cloud provided by the u-
blox CloudLocate service. Extends the life of energy-constrained
IoT applications. Low payload messages supported.

Code change (optional)

Geofencing

Not supported in current firmware.

Code change

Data logging

Not supported in current firmware.

Code change

Galileo return link message Galileo search and rescue (SAR) return link message UBX-RXM-

RLM.

Code change (optional)

RF spectrum view

New message. UBX-MON-SPAN shows in-band RF spectrum
around the GNSS band. This can be used to identify potential
in-band RF interference sources in the design.

Code change (optional)

Location batching

New feature that can be used to reduce power consumption by
saving navigation solutions on the receiver for up to 10 minutes
(at 1 Hz) and polling the solutions afterwards to a host MCU.

Code change (optional)

Protection level

New feature. Real-time position accuracy estimate with 95%
confidence level with the message UBX-NAV-PL.

Code change (optional)

Security

Message integrity

New feature. Authentication of data output based on private/
public key pair.

Code change (optional)

UBX-22038241 - R02

 

Appendix

Page 83 of 92

C1-Public

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Похожие инструкции для MAX-M10

TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Бренд: TCS Basys Controls Страницы: 2
Abus HomeTec Pro CFF3000 Operation preview
HomeTec Pro CFF3000
Бренд: Abus Страницы: 13
NAVITAS 440A Installation & Service Manual preview
440A
Бренд: NAVITAS Страницы: 7
Abus PLHA10000 Quick Manual preview
PLHA10000
Бренд: Abus Страницы: 2
Access Flow2 User'S Manual & Installation Instructions preview
Flow2
Бренд: Access Страницы: 12
BADODOSECURITY G200 Quick Manual preview
G200
Бренд: BADODOSECURITY Страницы: 8
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Бренд: Parker Страницы: 44
Valcom V-2003A Technical Specifications preview
V-2003A
Бренд: Valcom Страницы: 3
Valcom V-1092 User Manual preview
V-1092
Бренд: Valcom Страницы: 3
Valcom V-1092 Technical Specifications preview
V-1092
Бренд: Valcom Страницы: 2
B&G ZEUS S Detailed App Manual preview
ZEUS S
Бренд: B&G Страницы: 19
M-system R5-TS Instruction Manual preview
R5-TS
Бренд: M-system Страницы: 3
Carrier AQUASNAP 30RA "B" Operation & Maintenance Instructions Manual preview
AQUASNAP 30RA "B"
Бренд: Carrier Страницы: 36
Velux KUX 100 Instructions Manual preview
KUX 100
Бренд: Velux Страницы: 11
Kantronics KAM XL Reference Manual preview
KAM XL
Бренд: Kantronics Страницы: 201
S.E.A. Group Sundstrom SR307 Manual preview
Sundstrom SR307
Бренд: S.E.A. Group Страницы: 5
D+H CPS-M1-S Original Instructions Manual preview
CPS-M1-S
Бренд: D+H Страницы: 36
netvox RB02I User Manual preview
RB02I
Бренд: netvox Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды