manualshive.com logo in svg

Ublox MAX-M10, Руководство по интеграции

Поделиться
Скачать
Ublox MAX-M10 Скачать руководство пользователя страница 26

MAX-M10M - Integration manual

Following the start condition from the master, the 7-bit device address and the RW bit (which is a
logic low for write access) are clocked onto the bus by the master transmitter. The receiver answers
with an acknowledge (logic low) response to indicate that it is responsible for the given address.

The master can write 2 to N bytes to the receiver, generating a stop condition after the last byte
being written. To properly distinguish from the write access to set the address counter in random
read accesses, the number of data bytes must be at least 2.

Figure 9: I2C write access

3.2.3 PIOs

This section describes the PIOs supported by MAX-M10M. All PIO active voltage levels are related
to the V_IO supply voltage. All the inputs have internal pull-up resistors in normal operation and can
be left open if unused.

When assigning a different function to a PIO, ensure that the default function is disabled where
applicable. For example, disable the I2C interface with the CFG-I2C-ENABLED configuration key
if I2C pins are used for antenna supervisor functions.

3.2.3.1 RESET_N

MAX-M10M provides a RESET_N pin to reset the receiver. The RESET_N pin is input-only with an
internal pull-up resistor to V_IO and should be left open for normal operation. Driving RESET_N low
for at least 1 ms will trigger a reset of the receiver. The RESET_N complies with the V_IO level and
can be actively driven high.

Use RESET_N only in critical situations to recover the receiver. RESET_N resets the receiver and
clears the BBR content including receiver configuration, real-time clock (RTC), and GNSS orbit
data, triggering a cold start.

No capacitor should be placed at RESET_N to GND, otherwise it could trigger a reset on every
startup.

3.2.3.2 SAFEBOOT_N

The SAFEBOOT_N pin is for future service, updates and reconfiguration.

The  SAFEBOOT_N  pin  is  internally  connected  to  the  TIMEPULSE  pin  through  a  1  kΩ  series
resistor.

3.2.3.3 TIMEPULSE

The MAX-M10M features one time pulse output at the TIMEPULSE pin. This can only be configured
in PIO04. The details about this feature are explained in the section 

Time pulse

.

UBX-22038241 - R02

 

3 Receiver functionality

Page 26 of 92

C1-Public

Содержание MAX-M10





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды