Ublox MAX-M10 Скачать руководство пользователя страница 7

Страница: 7 / 92

MAX-M10M - Integration manual

1.3 Pin assignment

Figure 2: MAX-M10M pin assignment

Pin no.

Name

PIO no. I/O

Description

Remarks

GND

Connect to GND

TXD

UART TX

If not used, leave open. Alternative functions

RXD

UART RX

If not used, leave open. Alternative functions

TIMEPULSE

Time pulse signal

See section

TIMEPULSE

for more information.

Alternative functions

EXTINT

External interrupt

See

EXTINT

for more information. Alternative

functions

V_BCKP

Backup voltage
supply.

Leave open if no external backup supply. See

V_BCKP

for more information.

V_IO

IO voltage supply

See

V_IO

for more information.

VCC

Main voltage supply

See

VCC

for more information.

RESET_N

System reset (active
low)

It has to be low for at least 1 ms to trigger a reset. Leave
open if not used.
See

RESET_N

section for more information.

GND

Connect to GND

RF_IN

GNSS signal input

The RF signal line is DC blocked internally. The line
must match the 50 Ω impedance.
See sections

RF front-end

and

Layout

for more

information about the RF signal considerations.

GND

Connect to GND

LNA_EN

On/Oﬀ external LNA
or active antenna

See

LNA_EN

for more information.

VCC_RF

Output voltage RF
section

This pin supplies a ﬁltered voltage that can be used
for optional external active antenna or LNA. This pin
is internally connected to VCC through a ferrite bead.

Alternatively, this pin can be used for

. Care must be taken

when the assigned function sets the pin as an output.

UBX-22038241 - R02

1 System description

Page 7 of 92

C1-Public

Содержание MAX-M10





























































































Результаты поиска

Содержание MAX-M10

Отзывы:

Бренды по названию

Популярные бренды

Ublox MAX-M10, Руководство по интеграции

Результаты поиска

Содержание MAX-M10

Отзывы:

Бренды по названию

Популярные бренды