UAZ HUNTER 315195 Скачать руководство пользователя | Manualshive

Страница: 70 / 136

background image

70

replacement and tension of drive belts of the power steering

fan and pump, generator, cooling system pump, and high-

pressure fuel pump (HPfP)

From time to time, check the tension and condition of the
belts. Replace the belts when damaged or over-tensioned.

The power steering fan and pump drive belt shall be tensioned

as follows:
  - loosen bolt 4 (Fig. 9.14);
  - by turning one of the tension rollers 3, bring the belt
tension to the required value (for standard values, see Table
"Specifications");
  - tighten bolt 4.
  If you cannot achieve the specified tension using one roller,
use the second roller.
  The belt shall be replaced as per the following procedure:
  - loosen bolts 4;
  - by turning the rollers 3, release the belt tension;
  - replace the belt and tension it as specified above.

Fig. 9.14. Belt of the power steering fan and pump drive:

1 — power steering fan and pump drive belt; 2 — fan pulley; 3 — tensioning
roller; 4 — bolt; 5 — power steering pump pulley; 6 — crankshaft damping pulley

«
...
68
69
70
71
72
...
»

Содержание HUNTER 315195









































































































































Отзывы:

Нет отзывов

Похожие инструкции для HUNTER 315195

UNIVERSAL CJ-2A

Бренд: Jeep Страницы: 27

Бренд: Jeep Страницы: 228

Бренд: Jeep Страницы: 108

Бренд: Jeep Страницы: 525

Wallbox eM4 Single

Бренд: ABL Страницы: 68

WirelessAIR 73000EZ

Бренд: Air Lift Страницы: 12

Бренд: iOttie Страницы: 58

Бренд: PEUGEOT Страницы: 17

Бренд: Thule Страницы: 4

Бренд: TATA Motors Страницы: 232

Бренд: Car-Interface Страницы: 23

Prestige 128-8602

Бренд: Audiovox Страницы: 8

Бренд: Westin Страницы: 3

Бренд: Ford Страницы: 8

Бренд: Yakima Страницы: 12

Бренд: American muscle Страницы: 3

Бренд: TERAFLEX Страницы: 18

20111 Highlander

Бренд: Toyota Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды