TSUJI ELECTRONICS PM16C-16HW2 Скачать руководство пользователя страница 40

Страница: 40 / 75

6 Operation of Motor

<ch>: 0 ~ F(Hexadecimal) for channel



Continuous move commands

Command SCAN<d><ch>

Start continuous move.
Same as SCAN move on LOCAL mode.

Argument <d>

Direction

P/CW N/CCW

Reply Nothing

Example SCANN2 Start continuous move for CCW direction at CH2.

Remarks Only remote mode. And the motor is stopped.

Command CSCAN<d><ch>

Start constant-speed continuous move.
(No acceleration and deceleration)

Argument <d>

Direction

P/CW N/CCW

Reply Nothing

Example CSCANN2 Start continuous move for CCW direction at CH2.

Remarks

Only remote mode. And the motor is stopped.
Be careful of LSPD value, because too fast LSPD value causes motor step out.

Command SCANH<d><ch>

It is the same as “SCAN” command, except stop
moving if home position sensor activates. It is a move
that corresponds to the method 1 of the Home Position
Set and Search drive (page 17).

Argument <d>

Direction

P/CW N/CCW

Reply Nothing

Example SCANHN2 Start continuous move for CCW direction at CH2.

Remarks Only remote mode. And the motor is stopped.

Содержание PM16C-16HW2












































































Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды

TSUJI ELECTRONICS PM16C-16HW2, Руководство пользователя

Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды