TSUJI ELECTRONICS PM16C-16HW2 Скачать руководство пользователя страница 64

Страница: 64 / 75

4. In order to enter “4”, move the cursor to the location where colored in the figure above.

Please press the numeric keypad “9” 3 times.
The input was completed, and "A-4" has been set in the comments of CH1.



How to set the channel comments (remote mode)
The configuration and verification command of the channel comment is as follows.

<ch>: 0 ~ F(Hexadecimal) for channel.

Command CHCMNT<ch> <cmt>

Set the comment to channel.

Argument <cmt>

comment

Please enter alphanumeric up to three
characters.

Initial value CH<ch>

Reply Nothing

Example CHCMNTA A-3 Set the comment “A-3” to CH10.

Remarks Only remote mode.

Command CHCMNT?<ch>

You can confirm the channel comments. You can
check the comments of all channels, if you enter
"a" to <ch>.

ccc Comment is returned.
ccc ccc ccc ... ccc If you send a "CHCMNT?a",

the comments are returned with separation by space
in ascending order from ch0.

Example CHCMNT?A reply:A-3

Remarks

Содержание PM16C-16HW2












































































Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды

TSUJI ELECTRONICS PM16C-16HW2, Руководство пользователя

Результаты поиска

Содержание PM16C-16HW2

Отзывы:

Похожие инструкции для PM16C-16HW2

Бренды по названию

Популярные бренды