TSUJI ELECTRONICS PM16C-16HW2 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 75

background image

6 Operation of Motor

41

*Backlash adjustment move

When you execute absolute or relative move, moves extra backlash adjustment value
before reaching the destination point.
For example, adjustment value is +500, moves destination point plus 500 point and
moves relative -500 value. Backlash adjustment move pattern is changed by sign of
adjustment value and motor move direction. Please see the example below.

Ex.1) Move direction is CW and adjustment value is positive

Ex.2) Move direction is CW and adjustment value is negative

If move direction is CCW, these two drive routine are exchanged.
Backlash adjustment value is checked and changed at Page 2 on SETUP mode or
this command.
<ch>: 0 ~ F(Hexadecimal) for channel

Command B?<ch>

Check the backlash adjustment value.

Reply

±

dddd (signed 4 digit decimal.)

Example B?3 Reply: +0500 Backlash adjustment value of CH3 is 500.

Remarks

Command B<ch><deg>

Set the backlash adjustment value.

Argument <deg>

Value

-99,999 ~ +99,999

Initial value +100

Reply Nothing

Example B0+400 Set backlash adjustment value of CH3 to 500.

Remarks Only remote mode. And the motor is stopped.

CW

Without backlash adjustment move

With backlash adjustment move

CCW

destination

desti
backlash adjustment value

destination

desti
backlash adjustment value

CW

CCW

Without backlash adjustment move

With backlash adjustment move and auto adjust

With backlash adjustment move and no auto adjust

«
...
40
41
42
43
44
...
»

Содержание PM16C-16HW2












































































Отзывы:

Нет отзывов

Похожие инструкции для PM16C-16HW2

Бренд: Vacon Страницы: 62

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: Kasco Страницы: 3

Бренд: C Prox Ltd Страницы: 5

Бренд: Samson Страницы: 40

Бренд: Samson Страницы: 20

BT300 BurnerTronic

Бренд: Lamtec Страницы: 48

Бренд: YUGE Страницы: 69

Бренд: Quectel Страницы: 232

Бренд: Quectel Страницы: 9

Бренд: Quectel Страницы: 73

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды