TSUJI ELECTRONICS PM16C-16HW2 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 75

background image

8 Timing out signal output

60

<ch>: 0 ~ F(Hexadecimal) for channel.

Output channel fixed mode when enabled, Set up the output channel by the command below.
Confirmation is possible at any time, but the settings have not reflected that it is not the fixed
mode.

Supplement: For channel switching of the timing signal output channel fixed mode

In timing signal output channel fixed mode, switching of the LCD display channel
is possible by CH SEL switch "SETCH" command, even if it is the remote mode.

Command TMGFX?

Confirm the output channel mode of the timing signal.

Reply

DS/ Output from the channel in the display.
EN/ Output channel fixed mode

Example TMGFX? reply: EN

Remarks

Command

TMGCH

<ch><ch><ch><ch>

Set the channel of the timing signal.

Argument <ch>

channel

In order to TP3 from TP0, must be entered in
hexadecimal notation the channel to output the
signal. Please enter "-" in place that does not change
the display. Can not be set at the same time two or
more the same ch.

Reply Nothing

Example TMGCH48CF Set TP0: CH4, TP1: CH8, TP2 CH12, TP3: CH15.

Remarks

It is effective when the timing signal output channel fixed mode.
At remote mode, before setting and after setting, it is effective when both channels are
stopped.
In remote mode, it is effective when both channels (before setting and after setting)
are stopped.

Command

TMGCH?

Confirm the channel of the timing signal.

Reply <ch><ch><ch><ch> order: TP0,TP1,TP2,TP3 (hexadecimal)

Example TMGCH? Reply: 48CF

Remarks

«
...
59
60
61
62
63
...
»

Содержание PM16C-16HW2












































































Отзывы:

Нет отзывов

Похожие инструкции для PM16C-16HW2

VLT AQUA Drive FC 202

Бренд: Danfoss Страницы: 124

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 114

ECL Comfort 300

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 8

ECL Comfort 296

Бренд: Danfoss Страницы: 159

VLT AutomationDrive FC 301

Бренд: Danfoss Страницы: 78

Бренд: Danfoss Страницы: 20

ECL Comfort 210

Бренд: Danfoss Страницы: 12

ECL Comfort 110

Бренд: Danfoss Страницы: 8

ECL Comfort 100M

Бренд: Danfoss Страницы: 21

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 64

Бренд: fakro Страницы: 16

Бренд: e-BLEACH Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды