Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 12

Страница: 12 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

12 / 133

TMCL Command Format

Bytes

Meaning

Module address

Command number

Type number

Motor or Bank number

Value (MSB ﬁrst!)

Checksum

Table 2: TMCL Command Format

Info

The checksum is calculated by accumulating all the other bytes using an 8-bit

addition.

Note

When using the CAN interface, leave out the address byte and the checksum byte.

With CAN, the CAN-ID is used as the module address and the checksum is not

needed because CAN bus uses hardware CRC checking.

3.1.1

Checksum Calculation

As mentioned above, the checksum is calculated by adding up all bytes (including the module address

byte) using 8-bit addition. Here are two examples which show how to do this:

Checksum calculation in C:

unsigned char

i, Checksum ;

unsigned char

Command [9];

// Set the Command array to the desired command

Checksum = Command [0];

for

(i =1; i <8; i ++)

Ch= Command [i];

Command [8]= Checksum ;

// insert checksum as last byte of the command

// Now , send it to the module

Checksum calculation in Delphi:

var

i, Checksum :

byte

;

Command :

array

[0..8]

of byte

;

Set

the Command

array to

the desired command

// Calculate the Checksum :

Checksum := Command [0];

for

i :=1

Checksum := Ch Command [i];

Command [8]:= Checksum ;

// Now , send the Command

array

(9 bytes )

the module

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды