Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 17

Страница: 17 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

17 / 133

Command

Number

Parameter

Description

RORA

Rotate right, velocity speciﬁed by ac-

cumulator

SIV

<value>

Set indexed variable

GIV

Get indexed variable

AIV

Accumulator to indexed variable

Table 5: Overview of all TMCL Commands

3.5

TMCL Commands by Subject

3.5.1

Motion Commands

These commands control the motion of the motor. They are the most important commands and can be

used in direct mode or in standalone mode.

Motion Commands

Mnemonic

Command number

Meaning

ROL

Rotate left

ROR

Rotate right

MVP

Move to position

MST

Motor stop

SCO

Store coordinate

CCO

Capture coordinate

GCO

Get coordinate

Table 6: Motion Commands

3.5.2

Parameter Commands

These commands are used to set, read and store axis parameters or global parameters. Axis parameters

can be set independently for each axis, whereas global parameters control the behavior of the module

itself. These commands can also be used in direct mode and in standalone mode.

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды