Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 100

Страница: 100 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

100 / 133

Number

Axis Parameter

Description

Range [Units]

Access

Maximum

current

Motor current used when motor is running. The

maximum value is 255 which means 100% of

the maximum current of the module.

The current can be adjusted in 32 steps:

0. . . 7

79. . . 87

160. . . 167

240. . . 247

8. . . 15

88. . . 95

168. . . 175

248. . . 255

16. . . 23

96. . . 103

176. . . 183

24. . . 31

104. . . 111

184. . . 191

32. . . 39

112. . . 119

192. . . 199

40. . . 47

120. . . 127

200. . . 207

48. . . 55

128. . . 135

208. . . 215

56. . . 63

136. . . 143

216. . . 223

64. . . 71

144. . . 151

224. . . 231

72. . . 79

152. . . 159

232. . . 239

The most important setting, as too high values can

cause motor damage.

0. . . 255

Standby

current

The current used when the motor is not running.

The maximum value is 255 which means 100% of

the maximum current of the module. This value

should be as low as possible so that the motor

can cool down when it is not moving. Please see

also parameter 214.

0. . . 255

Position

reached ﬂag

This ﬂag is always set when target position and

actual position are equal.

0/1

Home switch

state

The logical state of the home switch input.

0/1

Right limit

switch state

The logical state of the right limit switch input.

0/1

Left limit

switch state

The logical state of the left limit switch input.

0/1

Right limit

switch disable

Deactivates the stop function of the right limit

switch if set to 1.

0/1

Left limit

switch disable

Deactivates the stop function of the left limit

switch if set to 1.

0/1

Swap limit

switches

Swap the left and right limit switches when set

to 1.

0/1

Acceleration A1

First acceleration between VSTART and V1 (in

position mode only).

0. . . 7629278

[pps

]

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды