Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 50

Страница: 50 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

50 / 133

3.6.20

CSUB (Call Subroutine)

This function calls a subroutine in the TMCL program memory.

It is intended for standalone operation only.

Internal function:

the actual TMCL program counter value is saved to an internal stack, afterwards

overwritten with the passed value. The number of entries in the internal stack is limited to 8. This also

limits nesting of subroutine calls to 8. The command will be ignored if there is no more stack space left.

Related commands:

RSUB, JA.

Mnemonic:

CSUB <label>

Binary Representation

Instruction

Type

Motor/Bank

Value

0 (don’t care)

Example

Call a subroutine:

Loop :

MVP ABS , 0, 10000

CSUB SubW

// Save program counter and jump to label SubW

MVP ABS , 0, 0

CSUB SubW

// Save program counter and jump to label SubW

JA Loop

SubW :

WAIT POS , 0, 0

WAIT TICKS , 0, 50

RSUB

// Continue with the command following the CSUB command

Binary form of CSUB SubW

(assuming SubW at address

100)

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды