Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 62

Страница: 62 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

62 / 133

3.6.29

AAP (Accu to Axis Parameter)

The content of the accumulator register is transferred to the speciﬁed axis parameter. For practical usage,

the accumulator has to be loaded e.g. by a preceding GAP instruction. The accumulator may have been

modiﬁed by the CALC or CALCX (calculate) instruction.

This command is mainly intended for use in standalone

mode.

Info

For a table with parameters and values which can be used together with this

command please refer to section

Related commands:

AGP, SAP, GAP, SGP, GGP, GIO, GCO, CALC, CALCX.

Mnemonic:

AAP <parameter number>, <motor number>

Binary Representation

Instruction

Type

Motor/Bank

Value

see chapter

<value>

Reply in Direct Mode

Status

Value

100 - OK

don’t care

Example

Position motor #0 by a potentiometer connected to analog input #0:

Start :

GIO 0,1

// get value of analog input line 0

CALC MUL , 4

// multiply by 4

AAP 0,0

// transfer result to target position of motor 0

JA Start

// jump back to start

Binary Form of AAP 0, 0

Field

Value

Target address

Instruction number

Type

Motor/Bank

Value (Byte 3)

Value (Byte 2)

Value (Byte 1)

Value (Byte 0)

Checksum

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды