Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 108

Страница: 108 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

108 / 133

Number

Axis Parameter

Description

Range [Units]

Access

212

Maximum

encoder

deviation

When the actual position (parameter 1) and the

encoder position (parameter 209) differ more

than set here the motor will be stopped. This

function is switched off when the maximum de-

viation is set to zero.

0. . . 65535

[encoder

steps]

214

Power down

delay

Standstill period before the current will be

ramped down to standby current. The standard

value is 200 (which means 2000ms).

0. . . 417

[10ms]

251

Reverse shaft

Reverse the rotation direction of the motor

shaft.

0/1

255

Unit mode

Units of velocity and acceleration/deceleration

settings:

0 - the internal units of the motion controller are

used directly

1 - the units are pps for velocity and pps

for

acceleration/deceleration

Default value is 1 (pps units).

0/1

Table 16: All TMCM-1211 Axis Parameters

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды