Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 5

Страница: 5 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

5 / 133

Features

The TMCM-1211 is a single axis controller/driver module for 2-phase bipolar stepper motors with state

of the art feature set. It is highly integrated, offers a convenient handling and can be used in many

decentralized applications. The module has been designed for coil currents up to 2.8A RMS and 24V

DC supply voltage. It is also equipped with end switch inputs as well as some general purpose digital

inputs and outputs and one analogue input. With its high energy eﬃciency from TRINAMIC’s coolStep™

technology cost for power consumption is kept down. The TMCL ﬁrmware allows for both standalone and

direct mode operation.

Main characteristics

• Motion controller & stepper motor driver:

–

Hardware motion proﬁle calculation in real-time.

–

On the ﬂy alteration of motion parameters (e.g. position, velocity, acceleration).

–

High performance microcontroller for overall system control and communication protocol

handling.

–

Up to 256 microsteps per full step.

–

High-eﬃcient operation, low power dissipation.

–

Dynamic current control.

–

Integrated protection.

–

stallGuard2™ feature for stall detection.

–

coolStep™ feature for reduced power consumption and heat dissipation.

–

stealthChop™ feature for quiet motor operation.

• Interfaces

–

USB interface.

–

RS485 bus.

–

CAN bus.

–

Additional digital inputs and outputs.

–

One analogue input.

–

End switch inputs.

–

Step/direction input.

Software

TMCL remote controlled operation via USB, RS485 or CAN interface and/or stand-alone operation via TMCL

programming. PC-based application development software TMCL-IDE available for free.

Electrical data

• Supply voltage: +12V and +24V nominal (10. . . 27V DC supply range).

• Motor current: up to 2.8A RMS / 3.9A peak (programmable).

Please see also the separate Hardware Manual.

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды