Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 2

Страница: 2 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

2 / 133

Contents

Features

1.1

stallGuard2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2

coolStep

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3

sixPoint Motion Controller

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

First Steps with TMCL

2.1

Basic Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2

Using the TMCL Direct Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3

Changing Axis Parameters

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4

Testing with a simple TMCL Program

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TMCL and the TMCL-IDE — An Introduction

3.1

Binary Command Format

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1.1

Checksum Calculation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

Reply Format

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2.1

Status Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3

Standalone Applications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4

TMCL Command Overview

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5

TMCL Commands by Subject

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.1

Motion Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.2

Parameter Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.3

Branch Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.4

I/O Port Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.5

Calculation Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.6

Interrupt Processing Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5.7

New TMCL Commands

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6

Detailed TMCL Command Descriptions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.1

ROR (Rotate Right)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.2

ROL (Rotate Left)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.3

MST (Motor Stop)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.4

MVP (Move to Position)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.5

SAP (Set Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.6

GAP (Get Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.7

STAP (Store Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.8

RSAP (Restore Axis Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.9

SGP (Set Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.10 GGP (Get Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.11 STGP (Store Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.12 RSGP (Restore Global Parameter)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.13 RFS (Reference Search)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.14 SIO (Set Output)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.15 GIO (Get Input)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.16 CALC (Calculate)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.17 COMP (Compare)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.18 JC ( Jump conditional)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.19 JA ( Jump always)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.20 CSUB (Call Subroutine)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.21 RSUB (Return from Subroutine)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.22 WAIT (Wait for an Event to occur)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.23 STOP (Stop TMCL Program Execution – End of TMCL Program)

. . . . . . . . . . . . . .

3.6.24 SCO (Set Coordinate)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.6.25 GCO (Get Coordinate)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Бренды по названию

Популярные бренды