Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 114

Страница: 114 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

114 / 133

Module Speciﬁc Hints

This section contains some hints that are speciﬁc to the TMCM-1211 module.

6.1

General Purpose Inputs and Outputs

The TMCM-1211 module is equipped with six general purpose digital lines. Each of these can either be

used as an input or as an output. This can be selected using global parameter #78. For historical reasons

(compatibility with the ﬁrst TMCM-1110 stepRocker module), these inputs and outputs are named PWMU0,

PWMU1, PWMU2, PWMD0, PWMD1 and PWMD2.

Global parameter #78 is a bit vector where each bit determines if the corresponding digital line is an input

or an output. A bit that is clear means input, and a bit that is set means output.

Table

shows the relationship between the bits of global parameter #78 and the digital lines. Just add up

the values of all bits that are to be set (i.e. of those digital lines that are to be used as outputs) and set

global parameter #78 to this value.

Selection of Inputs and Outputs

Bit

Value

Digital I/O line

PWMU0

PWMU1

PWMU2

PWMD0

PWMD1

PWMD2

Table 21: Selection of Inputs and Outputs

For example, setting global parameter #78 to 7 (default value) programs PWMU0, PWMU1 and PWMU2 as

outputs and PWMD0, PWMD1 and PWMD2 as inputs.

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды