Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 26

Страница: 26 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

26 / 133

3.6.4

MVP (Move to Position)

With this command the motor will be instructed to move to a speciﬁed relative or absolute position. It

will use the acceleration/deceleration ramp and the positioning speed programmed into the unit. This

command is non-blocking - that is, a reply will be sent immediately after command interpretation and

initialization of the motion controller. Further commands may follow without waiting for the motor

reaching its end position. The maximum velocity and acceleration as well as other ramp parameters are

deﬁned by the appropriate axis parameters. For a list of these parameters please refer to section

The range of the MVP command is 32 bit signed (-2147483648. . . 2147483647). Positioning can be inter-

rupted using MST, ROL or ROR commands.

Three operation types are available:

• Moving to an absolute position in the range from -2147483648. . . 2147483647 (

−

...

−

• Starting a relative movement by means of an offset to the actual position. In this case, the new

resulting position value must not exceed the above mentioned limits, too.

• Moving the motor to a (previously stored) coordinate (refer to SCO for details).

Note

The distance between the actual position and the new position must not be

more than 2147483647 (

−

) microsteps. Otherwise the motor will run in

the opposite direction in order to take the shorter distance (caused by 32 bit

overﬂow).

Internal function:

A new position value is transferred to the axis parameter #0 (target position).

Related commands:

SAP, GAP, SCO, GCO, CCO, ACO, MST.

Mnemonic:

MVP

ABS|REL|COORD

axis

position|offset|coordinate

Binary Representation

Instruction

Type

Motor/Bank

Value

0 – ABS – absolute

position

1 – REL – relative

offset

2 – COORD – coordinate

0. . . 255

coordinate number (0..20)

Reply in Direct Mode

Status

Value

100 - OK

don’t care

Example

Move motor 0 to position 90000.

Mnemonic:

MVP ABS, 0, 90000

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды