ENGINEER GUIDE
Introduction
The Voice module provides audible information about the status
of your LightSYS system, and enables any remote, touch-tone
(DTMF) telephone to act as a keypad for the system.
Upon event occurrence, such as alarm activation, the Voice
module informs you of a security situation, for example intrusion
or fire, by calling you and playing a pre-recorded Event
announcement.
NOTE:
For programming the voice module, refer to
5IN1482 LightSYS
Installation Manual.
Dipswitches
SW Description Usage
1 Omit tamper Instead of a short with the TMP/COM
terminal block
2 OPT
Not in use
3 Test
Connected in parallel to all output
channels and enables to listen to all
played messages using a speaker (at
least 32 Ohm) connected between
the Test Spkr and COM terminals
4 Intern Mic
Select an external or internal
microphone for recording messages:
On:
Recording messages from the
microphone located on the Voice
module board.
Off:
Recording messages from a
microphone located on Listen / Talk
unit (IN1 terminal)
Wiring diagram
(See Fig.1)
:
When connecting the Listen/Talk unit to the Voice module it is
recommended to use one of the two types of wires for the IN and
OUT connections:
● Independently shielded wires: Used for Electro-magnetically
Noisy Environment/Long Distance. The shield should be
grounded (connected to COM terminal block).
● Independently twisted pared wires: Used for Electro-
magnetically Unquiet Environment/Middle Distance. The second
wire should be grounded (connected to COM terminal block).
Other types of wires can be used for Electro-magnetically Silent
Environment/Short Distance.
NOTES:
● Do not run wires close to power (110/230 VAC), high-voltage
wiring or any communication lines.
● Do not wrap or roll wires.
● All unused wires should be grounded by connecting them to the
COM terminal.
● The maximum distance between each Listen/Talk unit and the
Voice Module should not exceed 150 meter.
LEDs Indication:
Power:
The Power LED indicates the status of communication
between the Voice module and the Main Panel
Off:
No voltage power from the main panel
On:
There is normal communication with the Bus
Slow Flash:
The LED starts to flash 15 seconds after
communication with the Bus is interrupted, or during
installation mode
Rec / Play:
The Rec / Play Comm LED indicates the status of
communication between the Voice module and the remote
“Follow-Me” (FM) phone.
Condition Description
Off
There is no communication with the FM number.
On
FM communication has been established.
Slow Flash The Voice module is in the process of calling the
FM number.
Connectors
The Voice module board contains the following two connectors:
(See Fig.2)
● BUS (plug1): Used to connect the Voice module to the panel
via the 4-wire Bus. The AUX (RED), COM (BLK), BUS (YEL)
and BUS (GRN) terminals are identical to the BUS connector
and can be used for the same purpose.
● VOICE (plug2): Used to connect the Voice module to the
VOICE connector on the LightSYS Main Panel via the supplied
cable. This connector transmits signals from the Voice module
to the telephone line during remote communication, and is
essential for normal operation of the Voice module.
Technical Specifications
● Operating voltage: 13.8VDC +/-10%
● Current draw: 30 mA typical / 70 mA maximum
● Operating temperature: 0-70°C
● Main Panel Connection: wire BUS, ≤300 m from Main Panel
USER GUIDE
User Operation - Telephone Control
Commands
The LightSYS enables you to operate the system from a remote
touch-tone phone by initiating a telephone call to or from the
system and interacting with voice menus that guide you through
your required remote operation.
Receiving a call:
1. Pick up the phone.
2. Say “Hello” or press [#]. You will hear an event announcement
message.
3. Choose an option from the
Acknowledgment menu
.
Acknowledgment menu
Upon event occurrence, such as alarm activation, the system
informs you of security situations, for example, intrusion or fire,
by calling you and announcing a pre-recorded event announce-
ment message, followed by the Acknowledge menu.
After the Event Announcement message is made, the following
list of options is announced.
Operation Title:
Action
Description
(remotely by telephone)
Acknowledge Message
Press [1]
Acknowledging an event means that
you have received a message from
the security alarm system about a
relevant event in the system and
want to confirm this. After you
acknowledge an event, the system
calls the next FM number.
Acknowledge and stop all dialing Press [2] followed by
the code
This option acknowledges the event
and stops the system from calling the
next FM numbers to report the event.
Acknowledge and access the
Press [3] followed by
Operations menu
the code
The Operations menu lists the available
options for remotely operating your
system.
Listen In and Talk
Press [6] [3] followed by
the code
This option enables you to perform bi-
directional communication.
Repeat the event message
Press [#]
Repeat the Acknowledge menu Press [*]
Calling the System:
1. Dial the number of the premises.
● If an answering machine is present at the premises: Let the line
ring once, hang up and call again.
● If an answering machine is not in use at the premises: Wait
until the system picks up. You will hear a continuous tone.
2. After the tones, enter the 2-digit remote access code.
3. Enter your user code followed by [#].
4. Choose your option from the
Operations menu
.
Operations Menu:
The Voice Operations menu announces options and instructions
on how to use the system functions. The options in the
Operations menu vary according to system status and your
access rights.
Following is a list of the remote operations options:
Operation description
Action (remotely by telephone)
Setting all partitions Press [1][1]
Setting a selected partition Press [1][9] followed by the
partition number
Unsetting all partitions Press [2][2]
Unsetting a selected Press [2][9] followed by the
partition
partition number
Changing Zone Omit status Press [3] followed by the zone
number and then [#][9]
Operating Programming Press [4] followed by the output
Outputs
Changing Follow Me (FM) Press [5] followed by the FM
numbers
number and [#][2].
Enter the new phone number
and press [#][1].
Listen in to the premises Press [6][1]
Talking to the premises Press [6][2]
Listen and Talk to the Press [6][3]
premises
Recording messages that are
Press [7][1]… [5]
not included in the message
bank (5 messages)
Recording an opening message
Press [7][6]
Exiting the System
Press [0]
To return to the previous menu Press [*]
To repeat the menu options Press [#]
ENGLISH
Voice Module
Model: RP432EV
© RISCO Group 05/2011
5IN1545 B
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to
be free from defects in materials and workmanship under normal use for 24
months from the date of production. Because Seller does not install or connect the
product and because the product may be used in conjunction with products not
manufactured by the Seller, Seller cannot guarantee the performance of the
security system which uses this product. Seller's obligation and liability under this
warranty is expressly limited to repairing and replacing, at Seller's option, within a
reasonable time after the date of delivery, any product not meeting the
specifications. Seller makes no other warranty, expressed or implied, and makes
no warranty of merchantability or of fitness for any particular purpose.
In no case shall seller be liable for any consequential or incidental damages for
breach of this or any other warranty, expressed or implied, or upon any other basis
of liability whatsoever.
Seller's obligation under this warranty shall not include any transportation charges
or costs of installation or any liability for direct, indirect, or consequential damages
or delay.
Seller does not represent that its product may not be compromised or
circumvented; that the product will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise; or that the product will in all cases provide
adequate warning or protection.
Buyer understands that a properly installed and maintained alarm may only
reduce the risk of burglary, robbery or fire without warning, but is not insurance or
a guaranty that such event will not occur or that there will be no personal injury or
property loss as a result thereof.
Consequently seller shall have no liability for any personal injury, property
damage or loss based on a claim that the product fails to give warning. However,
if seller is held liable, whether directly or indirectly, for any loss or damage arising
under this limited warranty or otherwise, regardless of cause or origin, seller's
maximum liability shall not exceed the purchase price of the product, which shall
be complete and exclusive remedy against seller.
No employee or representative of Seller is authorized to change this warranty in
any way or grant any other warranty.
WARNING:
This product should be tested at least once a week.
UK
Tel: 44-(0)-161-655-5500
ITALY
Tel: +39-02-66590054
SPAIN
Tel: +34-91-490-2133
FRANCE
Tel: +33-164-73-28-50
BELGIUM
Tel: +32-2522-7622
U.S.A
Tel: +1-631-719-4400
RISCO Group Contacting Info
RISCO Group is committed to customer service and product support.
You can contact us through our website (www.riscogroup.com) or at the
following telephone and fax numbers:
All rights reserved.
No part of this document may be reproduced in any form without prior
written permission from the publisher.
BRAZIL
Tel: +55-11-3661-8767
CHINA (Shanghai)
Tel: +86-21-52-39-0066
CHINA (Shenzhen)
Tel: +86-755-82789285
POLAND
Tel: +48-22-500-28-40
ISRAEL
Tel: +972-3-963-7777
(LED1)
MIC1
VOICE MODULE
Voice
(to panel)
Message Box
LED TMP
Out
In1
In3
In2
C
1 2 3 4
DIP SW1
Intrnl MIC
OPT
Bypass Tamper
Test
Rec
Play
COM
AUX
Test Spkr
