Trane IntelliPak SCRG-020 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 52

background image

SETPOINT Menu

PKG-SVP01E-EN

39

For Default OA Damper Min Position, Use

Used With: All Units when an airside or
waterside economizer or VCM is installed.
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, REMOTE MIN POS POT INPUT

Setpoint From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Min Outside Air Flow Rate Ctrl, Use

Used With: Units with a VCM or GBAS installed.
Factory Presets: HI (KEYPAD) SETPOINT
MENU
Possible Values: HI (KEYPAD) SETPOINT
MENU, GBAS 0-5VDC Module

Setpoint From: HI (KEYPAD) SETPOINT MENU

1.

Press the NEXT key until the following screen is displayed.

For Supply Air Pressure Control, Use

Used With: AUnits with a IGV or VFD and GBAS
installed.
Factory Presets: HI (KEYPAD) SETPOINT
Menu
Possible Values: HI (KEYPAD) SETPOINT
MENU, GBAS 0-5VDC Module

Setpoint From: HI(KEYPAD) SETPOINT Menu

1.

Press the NEXT key until the following screen is displayed (if applicable)

Used With: All units.

End Of Submenu (NEXT) To ENTER SETUP

1.

Press the NEXT key to leave the submenu and show following screen.

«
...
37
38
39
40
41
...
»

Содержание IntelliPak SCRG-020





















































Отзывы:

Нет отзывов

Похожие инструкции для IntelliPak SCRG-020

Бренд: Galanz Страницы: 30

Бренд: Mesa Living Страницы: 37

Бренд: Danby Страницы: 39

Бренд: Daikin Страницы: 16

Бренд: GE Страницы: 72

Бренд: ICP Страницы: 19

Бренд: Sinclair Страницы: 38

Depuro Plus 230

Бренд: Vortice Страницы: 72

Бренд: Sencor Страницы: 21

Бренд: Daikin Страницы: 20

Бренд: dirna Bergstrom Страницы: 72

Бренд: Trane Страницы: 55

Duplex Water-Cooled Hermetic CenTraVac

Бренд: Trane Страницы: 80

Бренд: Beurer Страницы: 12

Бренд: Daikin Страницы: 228

Бренд: Daikin Страницы: 18

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды