Trane IntelliPak SCRG-020 Скачать руководство пользователя страница 33

Страница: 33 / 52

Programming SETUP

PKG-SVP01E-EN

Actuator Setup

Water Economizer

Used With: All Units when a waterside
economizer is installed.
Factory Presets: 150 Sec
Possible Values: 1-255 Sec

Max Stroke Time

150 Sec

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Economizer

Used With: All Units when a waterside
economizer is installed.
Factory Presets: 2.0 VDC
Possible Values: 0-10 VDC

Min Voltage

2.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Economizer

Used With: All Units when a waterside
economizer is installed.
Factory Presets: 10.0 VDC
Possible Values: 0-10 VDC

Max Voltage

10.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Economizer

Used With: All Units when a waterside
economizer is installed.
Factory Presets: Direct Acting
Possible Values: Direct Acting, Reverse Acting

Direct/Reverse Acting

Direct Acting

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Econ Bypass

Used With: All Units when a waterside
economizer is installed.
Factory Presets: 150 Sec
Possible Values: 1-255 Sec

Max Stroke Time

150 Sec

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Econ Bypass

Used With: All Units when a waterside
economizer is installed.
Factory Presets: 2.0 VDC
Possible Values: 0-10 VDC

Min Voltage

2.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Econ Bypass

Used With: All Units when a waterside
economizer is installed.
Factory Presets: 10.0 VDC
Possible Values: 0-10 VDC

Max Voltage

10.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup

Water Econ Bypass

Used With: All Units when a waterside
economizer is installed.
Factory Presets: Direct Acting
Possible Values: Direct Acting, Reverse Acting

Direct/Reverse Acting

Direct Acting

Press the NEXT key until the following screen is displayed.

Actuator Setup IGV/VFD Cmd

Used With: All Units when IGV/VFD is installed
Factory Presets: 150 Sec
Possible Values: 1 - 255 Seconds

Max Stroke Time

150 Sec

Press the NEXT key until the following screen is displayed.

Actuator Setup IGV/VFD Cmd

Used With: All Units when IGV/VFD is installed
Factory Presets: 2.0 VDC
Possible Values: 0 to 10 VDC

Min Voltage

2.0 VDC

Note:

Min. voltage should be set to 2.0 on units with IGV.

Press the NEXT key until the following screen is displayed.

Actuator Setup IGV/VFD Cmd

Used With: All Units when IGV/VFD is installed
Factory Presets: 10.0 VDC
Possible Values: 0 to 10.0 Volts DC

Max Voltage

10.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup IGV/VFD Cmd

Used With: All Units when IGV/VFD is installed
Factory Presets: DIRECT ACTING
Possible Values: DIRECT ACTING, REVERSE
ACTING

Direct/Reverse Act

DIRECT ACTING

Press the NEXT key until the following screen is displayed.

Содержание IntelliPak SCRG-020





















































Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды

Trane IntelliPak SCRG-020, Руководство по программированию

Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды