Trane IntelliPak SCRG-020 Скачать руководство пользователя страница 25

Страница: 25 / 52

Programming SETUP

PKG-SVP01E-EN

End of Submenu (NEXT) to Enter SETUP

Press the NEXT key to leave the submenu and show following screen.

Economizer Control Functions Submenu

Used with: Units with an airside or waterside
conomizer.
Possible Values: Waterside Econ, Airside Econ

Press ENTER to Review or Adjust

Pressing the NEXT key will bypass this section.

Economizer Priority

Used with: Units with an airside or waterside
conomizer
Possible Values: Waterside Econ, Airside Econ

Choose Which Economizer Stages Up First

Press the + or - key until the proper value is displayed.

Unocc Water Economizer Function:

ENABLED

Used With: Units with a waterside economizer
installed
Factory Presets: Enabled
Possible Values: Enabled, Disabled

Press the NEXT key until the following screen is displayed.

Unocc Air Economizer Function:

ENABLED

Used With: All Units when an airside
economizer is installed
Factory Presets: Enabled
Possible Values: Enabled, Disabled

Press the NEXT key until the following screen is displayed.

Disable WS Econ If Difference Between MA

Used With: Units with a waterside economizer
installed

Temp and Ent Water Temp Less Than 4.0 F

Press the NEXT key until the following screen is displayed.

End of Submenu (NEXT) to Enter SETUP

Press the NEXT key to leave the submenu and show following screen.

Press PREVIOUS to page back through the submenu.

Water Flow Control Setup Submenu

Used With: All units water-cooled and all units
with waterside economizer installed

Press ENTER to Review or Adjust

Press the NEXT key until the following screen is displayed.

Periodic Water Purge Function: Enabled

Used With: All units water-cooled and all units
with waterside economizer installed
Possible Values: Enabled, Disabled; Interval
= 1-999 Hrs; Duration = 1-9 Min

Interval: 1Hr Duration: 1 Min

Press the NEXT key until the following screen is displayed.

Water-Flow Init Time Delay: 1 Min

Used With: All units water-cooled and all units
with waterside economizer installed
Possible Values: 0-20 Min

Time to Establish Water Flow Before Diag

Press the NEXT key until the following screen is displayed.

Temp Stabilization Time Delay: 1 Min

Used With: All units water-cooled and all units
with waterside economizer installed
Possible Values: 0-20 Min

Water Flow Time for Valid Temp Readings

Press the NEXT key until the following screen is displayed.

Head Pressure Control Inactive Min: 10%

Used With: All units water-cooled units
Possible Values: 0-100%

Head Pressure Control Active Min: 30%

Pressing the NEXT key will bypass this section.

Содержание IntelliPak SCRG-020





















































Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды

Trane IntelliPak SCRG-020, Руководство по программированию

Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды