Trane IntelliPak SCRG-020 Скачать руководство пользователя страница 32

Страница: 32 / 52

Programming SETUP

PKG-SVP01E-EN

Device Charatcteristic Setup Definitions

To change device characteristics values on a particular

screen:

Press the plus or minus key until the correct value
appears in the screen.

2. Press the ENTER key to confirm your choice. If you’ve

made an error, press the CANCEL key to delete your
entry.

To navigate to another screen:

Press the NEXT key to advance to the next screen or

a. if no further changes are required and you want to

exit back to view the unit operating status, press the
STATUS key once, or

b. if you want to remain in the Device Characteristics

Setup Dfinitions submenu, press the SETUP key
once and it will return you to the bginning of that
particular submenu, or

c. if you want to exit to another submenu in the SETUP

menu, press the SETUP key twice. Then press the
NEXT key to scroll through the SETUP choices, or

d. if you want to exit to another menu, such as

CONFIGUREATION, press that key once, then press
the NEXT key to scroll through those screens.

Temperature Calibration Offset For

Used With: Water-cooled units and /or units
with waterside economizer is installed
Factory Presets: 0.0 F
Possible Values: 0.0-5.0 F

Ckt 2 Sat Cond Temp Input

0.0 F

Press the NEXT key until the following screen is displayed.

Temperature Calibration Offset For

Used With: Water-cooled units and /or units
with waterside economizer is installed
Factory Presets: 0.0 F
Possible Values: 0.0-5.0 F

Ckt 3 Sat Cond Temp Input

0.0 F

Press the NEXT key until the following screen is displayed.

Temperature Calibration Offset For

Used With: Water-cooled units and /or units
with waterside economizer is installed
Factory Presets: 0.0 F
Possible Values: 0.0-5.0 F

Ckt 4 Sat Cond Temp Input

0.0 F

Press the NEXT key until the following screen is displayed.

End of Submenu (NEXT) to Enter SETUP

Press the NEXT key to leave the submenu and show following screen.

Device Characteristic Setup Definitions

Used with: All Units

Press ENTER to review or Adjust

Pressing the NEXT key will bypass this section.

Actuator Setup

OA Damper

Used With: All Units when an airside
economizer is installed.
Factory Presets: 150 Seconds
Possible Values: 1 - 255 Seconds

Max Stroke Time

30 Sec

Press the NEXT key until the following screen is displayed.

Actuator Setup

OA Damper

Used With: All Units when an airside
economizer is installed.
Factory Presets: 2.0 VDC
Possible Values: 0.0 to 9.9 Volts DC

Min Voltage

2.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup

OA Damper

Used With: All Units when an airside
economizer is installed.
Factory Presets: 10.0 VDC
Possible Values: 0.1 to 10.0 Volts DC

Max Voltage

10.0 VDC

Press the NEXT key until the following screen is displayed.

Actuator Setup

OA Damper

Used With: All Units when an airside
economizer is installed.
Possible Values: DIRECT ACTING, REVERSE
ACTING

Direct/Reverse Act

DIRECT ACTING

Press the NEXT key until the following screen is displayed.

Содержание IntelliPak SCRG-020





















































Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды

Trane IntelliPak SCRG-020, Руководство по программированию

Результаты поиска

Содержание IntelliPak SCRG-020

Отзывы:

Похожие инструкции для IntelliPak SCRG-020

Бренды по названию

Популярные бренды