Toshiba HWS-P1105HR-E, Руководство по обслуживанию

Страница: 121 / 184

120
Function code table
FC Item Details Factory default
01 Water heat exchanger capacity *1 0012: P805XWH**-E 0015: P1105XWH**-E Depends on type
02 Cooling/Non-cooling switching 0000: Cooling 0001: Not cooling 0000: Cooling
08 Hot water boost operation time (operating time) 0003: 30 min - 0018: 180 min 0006: 60 min
09 Hot water boost set temperature 0040: 40 °C - 0080: 80 °C 0075: 75 °C
0A Anti bacteria set temperature 0065: 65 °C - 0080: 80 °C 0075: 75 °C
0B Anti bacteria holding time 0000: 0 min - 0060: 60 min 0030: 30 min
0C Mixing valve drive time 0003: 30 sec - 0024: 240 sec 0006: 60 sec
0F Hot water HP allowance while c hot water
supply 0000: Not allow - 0001: Allow 0000: Not allow
18 Upper limit of cooling set temperature 0018: 18 °C - 0030: 30 °C 0025: 25 °C
19 Lower limit of cooling set temperature 0007: 7 °C - 0018: 20 °C 0007: 7 °C
1A Upper limit of heating (ZONE1) set temperature 0037: 37 °C - 0060: 60 °C 0060: 60 °C
1B Lower limit of heating (ZONE1) set temperature 0020: 20 °C - 0037: 37 °C 0020: 20 °C
1C Upper limit of heating (ZONE2) set temperature 0037: 37 °C - 0060: 60 °C 0060: 60 °C
1D Lower limit of heating (ZONE2) set temperature 0020: 20 °C - 0037: 37 °C 0020: 20 °C
1E Upper limit of hot water set temperature 0060: 60 °C - 0080: 80 °C 0075: 75 °C
1F Lower limit of hot water set temperature 0040: 40 °C - 0060: 60 °C 0040: 40 °C
20 Hot water HP start temperature 0020: 20 °C - 0045: 45 °C 0038: 38 °C
21 Hot water HP stop temperature 0040: 40 °C - 0050: 50 °C 0045: 45 °C
22 Priority mode Hot water supply/Heating switching
temperature -0020: -20 °C - 0020: 20 °C 0000: 0 °C
23 Boiler output enable switching temperature -0020: -20 °C - 0020: 20 °C -0010: -10 °C
24 Outside air temperature for hot water temperature
compensation start -0020: -20 °C - 0010: 10 °C 0000: 0 °C
25 Hot water temperature compensation value 0000: 0K - 0015: 15K 0003: 3K
26 Night setback change temperature range 0003: 3K - 0020: 20K 0005: 5K
27 Set temperature shift with heating Auto -0005: -5K - 0005: 5K 0000: 0K
29 Outside air temperature T1 temperature -0015: -15 °C - 0000: 0 °C -0010: -10 °C
2B Outside air temperature T3 temperature 0000: 0 °C - 0015: 15 °C 0010: 10 °C
2C Set temperature A with outside air temperature of T0 0020: 20 °C - 0060: 60 °C 0040: 40 °C
2D Set temperature B with outside air temperature of T1 0020: 20 °C - 0060: 60 °C 0035: 35 °C
2E Set temperature C with outside air temperature of 0 °C 0020: 20 °C - 0060: 60 °C 0030: 30 °C
2F Set temperature D with outside air temperature of T3 0020: 20 °C - 0060: 60 °C 0025: 25 °C
30 Set temperature E with outside air temperature of 20 °C 0020: 20 °C - 0060: 60 °C 0020: 20 °C
31 Zone2 ratio with Zone1 as Auto 0000: 0% - 0100: 100% 0080: 80%
33 Hydro unit backup heater down time 0000: 5 min
0002: 15 min 0001: 10 min
0003: 20 min 0001: 10 min
34 Hydro unit backup heater up time 0000: 10 min
0002: 30 min 0001: 20 min
0003: 40 min 0000: 10 min
3A Frost protection function Invalid/Valid 0000: Invalid 0001: Valid 0001: Valid
3B Frost protection set temperature 0008: 8 °C - 0020: 20 °C 0015: 15 °C
3C 2-way valve operation (logical reverse) control 0000: Energised during cooling
0001: Not energised during cooling 0000: Activate during
cooling
3E Heating HP/Boiler priority switching when using boiler 0000: Priority on HP 0001: Priority on boiler 0000: Priority on HP
40 Activate/deactivate room temperature control 0000: Deactivate 0001: Activate 0000: Deactivate
*1 FC_01 is needed for PCB replacement or function code reset procedure has been completed.
*2 System restart with remote controller.
*3 Restart in the mode when stopping.
*4 In addition, it is enable only when switch 2-3 is set to “OFF” and FC61 is set to “3”.