Toshiba HWS-P1105HR-E, Руководство по обслуживанию

Страница: 122 / 184

121
52 External input contact logic (must be used in with
FC61) 0000: CLOSE to stop system *2
0001: OPEN to stop system *2
0002: OPEN to stop system, CLOSE to restart
system (Statics input)
0003: CLOSE to stop system, CLOSE again to restart
system (plus input) 0000:CLOSE to stop
54 Logic of 3-way valve’s action when powered (Single
return only) 0000: Not reversed (Hot water mode when powered)
0001: Reversed (Heating when powered) 0000: Not reversed
(Hot water mode when
powered)
58 Night setback is activated 0000: Zone 1 & 2
0001: Zone 1 only 0000: Zone1 & 2
59 Interval of Mixing Valve control 0001: 1 minute - 0030: 30 minutes 0004: 4 minutes
5A P1 setting while in hot water supply mode 0000: While running HP only
0001: P1 continues running 0000: While running
HP only
5B Boiler running setting 0000: Boiler and HP
0001: Boiler only with pump running
0002: Heater
0003: Boiler only (Pump stopping) 0003: Boiler only
61 Changing the target of stopping/starting by external
signal or changing the TEMPO setting 0000: Hot water supply and heating
0001: Keeping initial status *3
0002: Hot water supply only
0003: Heating only
0004: TEMPO1 (Not activate the heaters)
0005: TEMPO2 (Not activate the heaters, inlet pump,
heat pump) 0000: Hot water
supply and heating
62 Activate/deactivate A02 error detection 0000: Activate
0001: Deactivate 0000: Activate
64 Continuously run or stop the P2 pump while cooling 0000: Continuously run P2
0001: Stop P2 0000: Continuous
running
65 P1 pump setting when the thermostat is deactivated in
the room temperature remote controller and room
temperature thermostat settings 0000: Continuously run P1
0001: Stop P1 when the thermostat is OFF 0000: Continuous
running
67 Changing the condition of optional output (For the
optional PC board connected to CN209) 0000: 1-3 During defrosting
2-3 While compressor is running.
0001: 1-3 As error is detected
2-3 During operation 0000: 1-3 During
defrosting
2-3 While compressor
is running.
6E To diff temperature, when pump P1 stop at to 20 °C 0001: 1K 0005: 5K 0002: 2K
73 Hot water tank heater start time of heat-pump while
operating 0000: 30 min passed 0003: 120 min passed 0000: 30 min passed
92 Upper room temperature limit when cooling 0000: 0 °C - 0055: 55 °C 0029: 29 °C
93 Lower room temperature limit when cooling 0000: 0 °C - 0055: 55 °C 0018: 18 °C
94 Upper room temperature limit when heating 0000: 0 °C - 0055: 55 °C 0029: 29 °C
95 Lower room temperature limit when heating 0000: 0 °C - 0055: 55 °C 0018: 18 °C
96 Initial water temperature setting when controlling
cooling by the room temperature remote controller and
room temperature thermostat 0005: 5 °C - 0030: 30 °C 0020: 20 °C
9D Initial water temperature setting when controlling
heating by the room temperature remote controller and
room temperature thermostat 0020: 20 °C - 0060: 60 °C 0040: 40 °C
9E TO temperature setting to stop the P1 pump during the
middle period heating 0010: 10 °C - 0030: 30 °C 0020: 20 °C
A0 P1 pump speed control changes the percentage duty of
the PWM control 0000: 100% 0005: 50% 0000: 100%
A1 Outside air temperature T0 temperature -0030: -30 °C - -0020: -20 °C -0020: -20 °C
A2 Zone2 temperature setting method 0000: Percentage (FC31)
0001: Fixed value (FCA3~ A5) 0000: Percentage
A3 Set temperature A' with outside temperature of T0 0020: 20 °C - 0060: 60 °C 0040: 40 °C
A4 Set temperature B' with outside temperature of T1 0020: 20 °C - 0060: 60 °C 0035: 35 °C
FC Item Details Factory default
*1 FC_01 is needed for PCB replacement or function code reset procedure has been completed.
*2 System restart with remote controller.
*3 Restart in the mode when stopping.
*4 In addition, it is enable only when switch 2-3 is set to “OFF” and FC61 is set to “3”.