Toshiba HWS-P1105HR-E, Руководство по обслуживанию

Страница: 123 / 184

122
Remote controller function code table
*14~1A: for floor drying function
A5 Set temperature E' with outside temperature of 20 °C 0020: 20 °C - 0060: 60 °C 0020: 20 °C
B2 HP restart water temperature in A zone. (Valid only
room temp control using 2nd remote controller) 0020: 20 °C 0037: 37 °C 0025: 25 °C
B5 Initial water temperature setting method when
controlling heating by the room temperature remote
controller and room temperature thermostat 0000: The fixed temperature by FC9D
0001: The calculated temperature by Auto curve 0000: The fixed
B6 Changing the target of stopping / starting by external
signal (CN210 - terminal 2 and 3) 0000: none (Local hot water tank thermostat)
0001: Hot water supply control *4 0000: none
B8 Forcibly heater off at T0 ≥ A °C 0000: no restriction, 0001: 20 °C
0002: 15 °C, ···, 0006: -5 °C 0000: no restriction
B9 Backup heater energization temperature during
defrosting. Correction coefficient B
0000: 0K, ···, 0004: 40K 0000: 0K
BA Intermittent operation at T0 ≥ A °C
(heating mode)
0000: continuous operation
0001: 20 °C, ···, 0006: -5 °C 0000: continuous
operation
BB Intermittent operation at T0 < B °C
(cooling mode) 0000: continuous operation
0001: 35 °C, ···, 0003: 25 °C 0000: continuous
operation
BC Pump off time during thermostat off operation 0000: 5 min, ···, 0005: 30 min 0001: 10 min
FC Item Details Fist shipment
02 Temperature correction by the room temperature sensor
(heating) -10K~+10K: By 1K steps -1: -1K correction
03 Temperature correction by the room temperature sensor
(cooling) -10K~+10K: By 1K steps -1: -1K correction
05 24H/12H display switching 0: 24H display 1: 12H (AM/PM) display 0: 24H display
09 Night time low-noise mode 0: Invalid 1: Valid 0: Invalid
0A Night time low-noise start time 0 - 23 (0:00 to 23:00) 22: 22:00
0B Night time low-noise end time 0 - 23 (0:00 to 23:00) 06: 06:00
0C Anti bacteria start time 0 - 23 (0:00 to 23:00) 22: 22:00
0D Anti bacteria start cycle 1 - 10 (Every day to 10-day cycle) 07: 7-day cycle
0E Starting time of Night setback 0 - 23 (0:00 to 23:00) 22: 22:00
0F Ending time of Night setback 0 - 23 (0:00 to 23:00) 06: 06:00
11 Remote controller Alarm Tone. 0: Alarm Tone OFF 1: Alarm Tone ON 1: Alarm Tone ON
12 Frost running period (days) (0 days – 20 days) 00: No setting
13 Frost running period (hours) (0 hours – 23 hours) 00: No setting
14 Start and End temperature 20 - 55 (20 °C - 55 °C) 00: No setting
15 Max temperature 20 - 55 (20 °C - 55 °C) 00: No setting
16 Continuation days for every step up to Max temperature 1 - 7 (1 day - 7 days) 00: No setting
17 Temperature difference for every step up to Max
temperature 1 - 10 (1 K - 10 K) 00: No setting
18 Continuation days for every step down to End
temperature 1 - 7 (1 day - 7 days) 00: No setting
19 Temperature difference for every step down to End
temperature 1 - 10 (1 K - 10 K) 00: No setting
1A Continuation days in Max temperature 1 - 30 (1 day - 30 days) 00: No setting
FC Item Details Factory default
*1 FC_01 is needed for PCB replacement or function code reset procedure has been completed.
*2 System restart with remote controller.
*3 Restart in the mode when stopping.
*4 In addition, it is enable only when switch 2-3 is set to “OFF” and FC61 is set to “3”.