Toshiba E-Studio 5540c Скачать руководство пользователя страница 48

Страница: 48 / 118

1 TROUBLESHOOTING FOR THE HARDWARE

46 Clearing a Staple Jam

Close the front cover of the finisher.

Staple jam in the Saddle Stitch unit

Holding the knob, raise the guide, and return it to its
original position.

Remove the staples fallen between the staple
cartridge and the staple case or the ones in the staple
receiver.

Fit the staple cartridge into the stapler.

When fitting the staple cartridge, hold the green-labeled portion of the
bracket securely so that the bracket does not move.
Insert the cartridge until it is caught by the latch and secured with a
click.

Open the front cover of the finisher, and pull out the
Saddle Stitch unit until it stops.

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды