Toshiba E-Studio 5540c Скачать руководство пользователя страница 37

Страница: 37 / 118

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Jam 35

1 TROUBLESHOOTING FOR THE HARDWARE

Paper jam in the bridge unit

Do not touch the metal parts or motors of the bridge unit.

You could be burned or the shock could cause an injury to your hand.

Remove the jammed paper from the bridge unit after clearing all the other jams.

You must remove other jammed paper from the equipment before clearing paper from the bridge unit. Pulling the
bridge unit off the equipment without removing the jammed paper may cause the paper to be torn and left inside the
equipment.

Open the front cover of the equipment.

Putting your hand on the green lever, pull out the
bridge unit until it stops.

Holding the green lever, open the lower cover and
remove any paper under it.

Close the lower cover.

Содержание E-Studio 5540c























































































































Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды

Toshiba E-Studio 5540c, Руководство по устранению неисправностей

Результаты поиска

Содержание E-Studio 5540c

Отзывы:

Похожие инструкции для E-Studio 5540c

Бренды по названию

Популярные бренды